Package Contents; Safety Measures; Charging The Power Bank - Pulsar PB8I Instrucción

SKU
Type
Capacity, mAh
Charge voltage, V
Rated charge current, A
Rated voltage, V
Full charge time (hrs)
Full discharge time (I=250 mА)(at t=22 °С), hrs
Operating charge current, А
Charge/discharge temperature range
(relative humidity 60±5%)
Degree of protection, IP code (IEC60529)
Dimensions, mm / in.
Weight, kg / lbs.

PACKAGE CONTENTS

Pulsar PB8I Power Bank MicroUSB cable
DESCRIPTION
The Pulsar PB8I Power Bank is designed to extend operating time of digital and
thermal Pulsar devices equipped with a microUSB port (Signal RT, Photon RT, Trail,
Helion, Digisight Ultra, Digiforce RT etc.)
3

CHARGING THE POWER BANK

To check charge level, press and hold down the button (2). Green LEDs on the
charge indicator show the charge level:
Number of LEDs glowing (1-5); Charge level (20-100%)
1-20% / 2-40% / 3-60% / 4-80% / 5-100%
Connect the plug of the microUSB cable supplied to the Power Bank connector
(1) . Connect the other plug to the USB port (6) of your computer/laptop or USB
mains adapter.
The LEDs on the battery charge indicator (3) will light up.
As soon as the Power Bank charge level reaches 100%, all five LEDs will show
green.
4
USING THE POWER BANK WITH AN OPTICAL DEVICE
Connect the plug of the Power Bank microUSB cable (4) to the USB port (7) of your
optical device.
To turn the Power Bank on, briefly press the button (2). One LED will start blinking
– the Power bank will be in stand-by mode (for three minutes).
Turn the optical device on – the external power icon will appear in the status bar.
Power from the built-in batteries (or rechargeable) batteries will be turned off. The
LED indicator will stop blinking and go out.
1
79110
Li-Ion
5000
5
1.5
5
approx. 6
approx. 20
≤ 2
0 ... 45 °С / 32 °F... 113 °F
-20 ... +45 °С / -4 °F... 113 °F
IPX7
30x75x80 / 1.2x2.9x3.1
0.2 / 7
Warranty card
User manual
If your optical device is equipped with a Weaver rail, you may mount the Power
Bank on it with a fastening mechanism. Secure the Battery Pack by turning the
knob (5) fully.
Once the optical device has been disconnected, the Power bank switches to
stand-by mode (with one LED blinking). You may reconnect your optical device
within three minutes.
5

SAFETY MEASURES

When storing the battery for a long period it should be partially charged; the
battery should not be either fully charged or fully discharged.
Do not charge the battery immediately after bringing the battery from cold
environment into a warm one. Wait for 30-40 minutes for the battery to warm up.
Do not leave a battery unattended while charging.
Charge the battery at a temperature from 0 °C to +45 °C, otherwise batter's life will
decrease significantly.
Do not leave the battery connected to a computer for any longer than 24 hours
after full charge.
Do not expose the battery pack to high temperatures or to a naked flame.
Connection is not recommended of external devices with a power consumption
that exceeds permitted levels.
The battery is short-circuit protected. However, any situation that may cause
short-circuiting should be avoided.
Do not dismantle or deform the battery.
Do not drop or strike the battery.
When using the battery at below zero temperatures, battery's capacity decreases;
this is normal and is not a defect.
Do not use the battery at temperatures higher than those shown in the table – this
may reduce the battery's life.
Keep the battery out of reach of children.
1
6
4
7
5
3
2
2