Publicidad
IMAGINE
RGB CONTROLLER
PROPERTIES
• 3x4A
• 5~24V DC
• IP40
• Working Temperature -30~60º
• Range 15m (Open field)
2. LED output:
• Connect LED fixtures to this terminal. Install LED common anode cable
into the terminal marked with '+' and each channel LED cables into the
terminal marked with R, G, B. Please make sure the LED rated voltage is
same as the power supply and each channel's maximum load current is
below the controller rated current.
• The controller will run into protection if the output been overloaded or short
circuited. The indicator will flash red color and stop working in this case,
Please check the wiring and load current to remove the fault.
3. Work status indicator
• This indicator shows all working status of the controller. It displays different
events as following:
• Steady green: Normal working.
• Single green blink: Command received.
• Long single green blink: Mode or color cycle edge.
• Long single yellow blink: Brightness or speed limit.
• Red flash: Overload protection.
• Yellow flash: Over heat protection.
• Green flash 3 times: New remote controller paired.
FUNCTIONS
4. Turn ON / OFF
• Press 'I' key to turn on unit or press 'O' key to turn off. Main unit will memorize
the on/off status and will restore to the previous status on next power on.
• Please use remote controller to turn on the unit if it was switched to off
status before power cut.
WIRING & INDICATOR
1. Power supply input
• Install positive power cable into the terminal marked with '+' and negative
power cable into the terminal marked with '- '. The two positive jacks are
connected inside the controller and same for the negative jacks. The
controller can accept DC power from 5V to 24V, the output voltage is the
same as the power supply, so please make sure the LED rated voltage is
same as the power supply.
5. Static RGB color setting
• The keys in this area set the RGB static color and brightness.
• Press the colored keys to set the RGB LEDs to correspond color as shortcut.
• For other static colors, please press 'COLOR+' and 'COLOR-' key to select
from the preset library colors.
• Press the two sun-shaped keys to adjust color brightness.
6. Dynamic mode setting
• These keys control the RGB dynamic modes. Press 'MODE+' and 'MODE-'
to select dynamic modes and press 'SPEED+' and 'SPEED-' key to set the
running speed of the dynamic modes.
• Press 'DEMO' key to play the dynamic modes in loop with each mode
repeating for 3 times.
7. Remote indicator
• This indicator blinks when remote controller is working. If the indicator flash
slowly when pressing keys, it means the remote battery is nearly empty
and please change the battery in this case. The battery model is CR2032.
OPERATION
8. Using the remote controller
• Please pull out the battery insulate tape before using. The RF wireless remote
signal can pass through some nonmetal barrier. For proper receiving
remote signal, please do not install the controller in closed metal parts.
9. Pair a new remote controller
• The remote controller and main unit is 1 to 1 paired as factory default. It's
possible to pair maximum 5 remote controllers to one main unit and each
remote controller could be paired to any main unit.
• User could pair a new remote controller to main unit by following two steps:
1. Plug off the power of main unit and plug in again after more than 5
seconds.
2. Press 'SPEED-' and 'SPEED+' key simultaneously for about 3 seconds, in
time of 10 seconds after the main unit powered on.
10. Keep current remote only
• In some cases, one main unit might be paired with several remote
controllers but extra remote controllers are no longer needed. User could
simply pair the current using remote to main unit again, then the main unit
will dis-pair all other remote controllers and recognize current one only.
11. Protection
• The main unit has full protection function for wrong wiring, output short
circuit, overload and overheat. The controller will protect itself from
damage at these extreme conditions and could automatically recover
when working condition is good.
• Please ensure the LED fixtures are capable for constant voltage driving and
in rated range, the cables are well connected and insulated. Also please
install the controller with good ventilation and heat dissipation condition.
Publicidad
