Gate House G2X2D01 Instrucciones De Funcionamiento

ELECTRONIC KEYPAD DEADBOLT
ELECTRONIC DEADBOLT
Questions
Questions/¿Preguntas?
USER GUIDE
Call customer service at 1-877-442-8347,
8:00 a.m. - 8:00 p.m., EST, Monday - Friday.
Do not use any chemical liquid or lubricating oil with additives to clean the lock body .
It will damage the surface or even mainboard.
Unit Interface
ELECTRONIC DEADBOLT ELECTRONIC DEADBOLT
6
USER GUIDE USER GUIDE
7
1
R
Do not use any chemical liquid or lubricating oil with additives to clean the lock body . Do not use any chemical liquid or lubricating oil with additives to clean the lock body .
2 3 4
1 5
It will damage the surface or even mainboard. It will damage the surface or even mainboard.
2
8
7 9
6 0
Unit Interface Unit Interface
8
3
6 6
4
1 5
Programming Button Battery Lid
Programming button is for entering codes, Slide the lid to change the batteries.
1 1 R
clearing errors and setting functions.
It is also used to lock the door. 6
3 3 Battery Holder
2 4 2 4
1 1 5 5
2 2
7 8 9 7 8 9
Four AA (1.5 V) alkaline batteries
6 6 0 0
2 Number Buttons
(not included).
To enter user codes. Each user code is
7 R Button (Reset)
3 3
Restore default settings.
3 Cylinder
To lock/unlock the lockset from outside. 4 4 Turn-piece
8
To lock/unlock the lockset from inside.
4 Washer
1 1
Programming Button Programming Button
Prevents water from permeating into lockset.
Programming button is for entering codes, Programming button is for entering codes,
clearing errors and setting functions. clearing errors and setting functions.
It is also used to lock the door. It is also used to lock the door.
Operating Instructions
2 Number Buttons 2 Number Buttons
To enter user codes. Each user code is To enter user codes. Each user code is
Keep the door open while programming to avoid being locked out accidentally.
The lock contains one factory-preset user code but can be programmed to
3 3
Cylinder Cylinder
store up to a total of six additional unique user codes.
Codes can be added and deleted at any time. For first-time programming, use factory To lock/unlock the lockset from outside. To lock/unlock the lockset from outside.
default programming code. It's recommended to change the default programming code
4 Washer 4 and default user code right after you install the lock. Washer
Prevents water from permeating into lockset. Prevents water from permeating into lockset.
Operation Indicator Sounds and Lights
Lights
Sounds
Operating Instructions Operating Instructions
1 Beep Flashes Green Once Successful Operation
2 Long Beeps Flashes Green Twice Successful Programming
Keep the door open while programming to avoid being locked out accidentally. Keep the door open while programming to avoid being locked out accidentally.
The lock contains one factory-preset user code but can be programmed to The lock contains one factory-preset user code but can be programmed to
3 Beeps
Flashes Red 3 Times Operation Error
store up to a total of six additional unique user codes. store up to a total of six additional unique user codes.
Code Input Error; System Shuts
Codes can be added and deleted at any time. For first-time programming, use factory Codes can be added and deleted at any time. For first-time programming, use factory
5 Beeps Flashes Red 5 Times
Down for 45 seconds
default programming code. It's recommended to change the default programming code default programming code. It's recommended to change the default programming code
and default user code right after you install the lock. and default user code right after you install the lock.
10 Rapid Beeps Low Battery Power
Flashes Red 10 Times
Flashes Orange 3 Times Default Setting Restored
Operation Indicator Sounds and Lights Operation Indicator Sounds and Lights
Flashes Orange Slowly In Programming Mode
Sounds Sounds Lights Lights
1 Beep 1 Beep
Flashes Green Once Flashes Green Once
FEDERAL COMMUNICATIONS COMMISSION STATEMENT
2 Long Beeps 2 Long Beeps
Flashes Green Twice Flashes Green Twice
This device complies with Part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may
3 Beeps 3 Beeps
Flashes Red 3 Times Flashes Red 3 Times
cause undesired operation. Changes or modications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
5 Beeps 5 Beeps
Flashes Red 5 Times Flashes Red 5 Times
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
10 Rapid Beeps 10 Rapid Beeps Flashes Red 10 Times Flashes Red 10 Times
equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Flashes Orange 3 Times Flashes Orange 3 Times
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
Flashes Orange Slowly Flashes Orange Slowly
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
66482 / 02 SAFETY INFORMATION
Read the precautions and instructions in this manual before installing
Item #0817538
and using this lock. Save this manual for future reference.
WARNING: Do not use an electric screwdriver during installation.
Model #G2X2D01
CAUTION : Please use four alkaline batteries (not included) for the best performance.
A. Do not attempt to disassemble any internal components of
the lockset. Doing so will void the limited warranty.
Default programming code (PC): 0000
B. Do not drop or hit the lockset. Too much shock may result in permanent damage.
Default user code (UC): 1234
C. Do not use pins or sharp objects to press the keypad.
Your new programming code (PC) ____________ D. Always create a backup of information you wish to
keep (Programming Code, user code, etc.).
Your new user code (UC) ___________________
E. Promptly change the Programming Code before operating this lockset.
The same programming code and user code cannot be accepted.
ATTACH YOUR RECEIPT HERE
The lock will cease operation if unauthorized codes are entered more than
Serial Number
5 times. The system will unfreeze after 45 seconds.
Purchase Date
1
Door Handing Identification Process
The lock needs to learn if your door is a right-
Default programming code (PC): 0000 Default programming code (PC): 0000
!
Default user code (UC): 1234 Default user code (UC): 1234
Your new programming code (PC) ____________ Your new programming code (PC) ____________
DO THIS FIRST
Your new user code (UC) ___________________ Your new user code (UC) ___________________
2
Change Programming Code
The same programming code and user code cannot be accepted. The same programming code and user code cannot be accepted.
5
The lock will cease operation if unauthorized codes are entered more than The lock will cease operation if unauthorized codes are entered more than
Enter PC.
5 times. The system will unfreeze after 45 seconds. 5 times. The system will unfreeze after 45 seconds.
3
Add New User Code
1 1
Door Handing Identification Process
Enter PC. The lock needs to learn if your door is a right-
Note: Up to 6 sets of user codes can be saved. User codes should be 4–10 digits in length.
4 Delete an Existing User Code
DO THIS FIRST
Enter PC.
2 2
Change Programming Code
5 5
5 Enter PC.
Delete All User Codes at Once
7 7
R Enter PC. 3 3
Add New User Code
Note: Auto-locking and keypad locking functions will be invalid when user codes are deleted.
Enter PC.
The lock can only be operated by key during that time.
6 Toggle Auto-Lock On/Off Note: Up to 6 sets of user codes can be saved. User codes should be 4–10 digits in length.
8 8
4 4
Enter PC. Delete an Existing User Code
Note: The preset delay-time is 30 seconds. You can change the time by following the instructions
Enter PC.
in Step 7. Repeat Step 6 to cancel the auto-locking function.
5 5
Delete All User Codes at Once
5 5
Battery Lid Battery Lid
7
Set Auto-Lock Time Delay
Slide the lid to change the batteries. Slide the lid to change the batteries.
Enter PC.
Enter PC.
6 6
Battery Holder Battery Holder
Note:
Four AA (1.5 V) alkaline batteries Four AA (1.5 V) alkaline batteries
Note: The delay time can be programmed for anywhere from 10 - 99 seconds
(not included). (not included).
6 Toggle Auto-Lock On/Off 6
8
Toggle Mute On/Off
7 R Button (Reset) 7 R Button (Reset)
Enter PC.
Restore default settings. Restore default settings.
Enter PC.
Note: The preset delay-time is 30 seconds. You can change the time by following the instructions
8 Turn-piece 8 Turn-piece
Note: Repeat Step 8 to toggle mute on and off.
To lock/unlock the lockset from inside. To lock/unlock the lockset from inside.
LED illumination will still function when mute is toggled on.
7 Set Auto-Lock Time Delay 7
9
Enable/Disable All User Codes
Enter PC.
Enter PC.
Meaning
Note: The delay time can be programmed for anywhere from 10 - 99 seconds
Note: Auto-locking and keypad locking functions will be invalid when user codes are disabled.
The lock can only be operated by key during the time.
8 Toggle Mute On/Off 8
Repeat the steps to enable the user codes again.
Enter PC.
10
Create a One-Time User Code 4–10 Digits Long
Note: Repeat Step 8 to toggle mute on and off.
Enter PC.
9 9
Enable/Disable All User Codes
Note: The one-time user code will automatically expire after it is used one time.
Enter PC.
Meaning Meaning
Successful Operation Successful Operation Note:
Successful Programming Successful Programming
Operation Error Operation Error
10 10
Create a One-Time User Code 4–10 Digits Long
Code Input Error; System Shuts Code Input Error; System Shuts
Down for 45 seconds Down for 45 seconds
Enter PC.
Low Battery Power Low Battery Power
Default Setting Restored Default Setting Restored
Note: The one-time user code will automatically expire after it is used one time.
In Programming Mode In Programming Mode
handed or left-handed.
Enter PC. 0
4 Enter New PC.
Door Handing Identification Process
The lock needs to learn if your door is a right- 1 Enter New UC. handed handed or left-handed. or left-handed.
! !
Enter PC. Enter PC.
0 0
DO THIS FIRST
Enter the UC
2
Change Programming Code you want to
delete.
Enter PC. 4 4 Enter New PC. Enter New PC.
3
Add New User Code
Enter PC. 1 1 Enter New UC. Enter New UC.
Note: Up to 6 sets of user codes can be saved. User codes should be 4–10 digits in length.
5
Delete an Existing User Code
Enter the UC Enter the UC
Enter PC. 2 2
you want to you want to
delete. delete.
Delete All User Codes at Once
Enter
seconds
Enter PC. 3 3
6
(10~99).
Auto-locking and keypad locking functions will be invalid when user codes are deleted. Note: Auto-locking and keypad locking functions will be invalid when user codes are deleted.
The lock can only be operated by key during that time. The lock can only be operated by key during that time.
Toggle Auto-Lock On/Off
Enter PC. 5 5
7
Note: The preset delay-time is 30 seconds. You can change the time by following the instructions
in Step 7. Repeat Step 6 to cancel the auto-locking function. in Step 7. Repeat Step 6 to cancel the auto-locking function.
Set Auto-Lock Time Delay
Enter Enter
seconds seconds
Enter PC. 6 6
8 (10~99). (10~99).
Note: The delay time can be programmed for anywhere from 10 - 99 seconds
Toggle Mute On/Off
Enter PC. 7 7
Note: Repeat Step 8 to toggle mute on and off.
Enter
LED illumination will still function when mute is toggled on. LED illumination will still function when mute is toggled on.
9
One Time
Code.
Enable/Disable All User Codes
Enter PC. 8 8
Auto-locking and keypad locking functions will be invalid when user codes are disabled. Note: Auto-locking and keypad locking functions will be invalid when user codes are disabled.
The lock can only be operated by key during the time. The lock can only be operated by key during the time.
Repeat the steps to enable the user codes again. Repeat the steps to enable the user codes again.
Create a One-Time User Code 4–10 Digits Long
Enter Enter
9 9
Enter PC. One Time One Time
Code. Code.
Note: The one-time user code will automatically expire after it is used one time.
CARE AND MAINTENANCE
THE FOLLOWING CARE INSTRUCTIONS SHOULD BE FOLLOWED TO ENSURE A
LONG LASTING FINISH:
1. Remove locks, or do not install locks, prior to painting your door.
2. Do not use any chemical liquid or lubricating oils with additives to clean the lock.
WARNING: The Manufacturer advises that no lock can provide complete security
11 by itself. This lock may be defeated by forcible or technical means, or evaded by
Restore Default Settings
entry elsewhere on the property. No lock can substitute for caution, awareness of
R
Press your environment, and common sense. Builder's hardware is available in multiple
performance grades to suit the application. In order to enhance security and reduce
Note: Press the button for more than 5 seconds; the programming
risk, you should consult a qualified locksmith or other security professional.
is reset back to the original factory codes once you hear 3
long beeps.
After restoring default settings, you must run the door
handing identifying process (#1) again before
programming any other functions.
Troubleshooting
11 Restore Default Settings 11 Restore Default Settings
Press Press R R
PROBLEM POSSIBLE CAUSE
Note: Press the button for more than 5 seconds; the programming Note: Press the button for more than 5 seconds; the programming
After installing the lockset and batteries,
The door-handing Refer to step1.
is reset back to the original factory codes once you hear 3 is reset back to the original factory codes once you hear 3
the door can't be locked and three short
identification process isn't
long beeps. long beeps.
beeps are emitted when you press the yet complete.
After restoring default settings, you must run the door After restoring default settings, you must run the door
Programming button.
handing identifying process (#1) again before handing identifying process (#1) again before
You've installed the lockset and batteries, Batteries were installed
Check to see if the battery polarities
programming any other functions. programming any other functions.
but you still get no response when you
incorrectly. have been reversed or if the battery is
press any button.
dead.
If so, re-install or change the battery.
Troubleshooting Troubleshooting
If not, please check to see if the cable is
properly connected.
When you are in the door-handing
Wrong door-handing or
Press the R button to restore the system
PROBLEM PROBLEM POSSIBLE CAUSE POSSIBLE CAUSE
identifying process, you get the red light change of the door-handing
to factory default setting and re-execute
After installing the lockset and batteries, After installing the lockset and batteries, in the memory. The door-handing The door-handing door-handing identifying process
flashing three times, and three short
the door can't be locked and three short the door can't be locked and three short
identification process isn't identification process isn't ( Refer to
beeps.
beeps are emitted when you press the beeps are emitted when you press the
yet complete. yet complete.
Programming button. Programming button.
Although you succeeded in the first
Low battery. Replace with new alkaline batteries.
execution of the door-handing identifying
You've installed the lockset and batteries, You've installed the lockset and batteries,
Batteries were installed Batteries were installed
process, the latch still doesn't work.
but you still get no response when you but you still get no response when you incorrectly. incorrectly.
(i.e. You can feel the motor attempting to
press any button. press any button.
run, but the latch bolt is stuck, and the
turnpiece can't be rotated.)
Although the electronic deadbolt has
The deadbolt latch is stuck First, take out one battery, then press
been functioning normally, the latch bolt due to a warped door or
When you are in the door-handing When you are in the door-handing any button on the front panel for electric
Wrong door-handing or Wrong door-handing or
suddenly locks up, and the turnpiece misaligned door.
discharge, and put the battery back in.
identifying process, you get the red light identifying process, you get the red light change of the door-handing change of the door-handing
inside can't be rotated, not even with a
The latch bolt will automatically
in the memory. in the memory.
flashing three times, and three short flashing three times, and three short
key.
re-detect its position.
beeps. beeps.
Note: If the latch gets stuck frequently,
please check and fix the alignment of
Although you succeeded in the first Although you succeeded in the first
Low battery. Low battery.
the deadbolt latch & strike plate.
execution of the door-handing identifying execution of the door-handing identifying
process, the latch still doesn't work. process, the latch still doesn't work.
(i.e. You can feel the motor attempting to (i.e. You can feel the motor attempting to
The door can be locked normally, but
run, but the latch bolt is stuck, and the run, but the latch bolt is stuck, and the The sensor did not sense Unlock the door with the key and
when you try to unlock it, you hear three position.
turnpiece can't be rotated.) turnpiece can't be rotated.) re-program the unit.
short beeps and the lock won't unlock
If the problem persists, call our customer
when you enter the user code and press
Although the electronic deadbolt has Although the electronic deadbolt has service department.
The deadbolt latch is stuck The deadbolt latch is stuck
the programming button.
been functioning normally, the latch bolt been functioning normally, the latch bolt
due to a warped door or due to a warped door or
suddenly locks up, and the turnpiece suddenly locks up, and the turnpiece misaligned door. misaligned door.
While the door is locked, you hear the
inside can't be rotated, not even with a inside can't be rotated, not even with a (1) The depth of the latch
(1) Dig the latch bolt hole for the strike
latch bolt coming out when you press
key. key.
bolt hole is insufficient.
deeper. The minimum depth is 1 in.
the Programming button to lock the
(2.5 cm).
door; however, three short beeps are
(2) The latch bolt is not
emitted. Conversely, while the door is
aimed at the opening
(2) Adjust the strike to the appropriate
open, no beeps are emitted when
of the strike.
position.
locking the latch bolt.
The door can be locked normally, but The door can be locked normally, but
The sensor did not sense The sensor did not sense
when you try to unlock it, you hear three when you try to unlock it, you hear three
position. position.
Warranty
short beeps and the lock won't unlock short beeps and the lock won't unlock
when you enter the user code and press when you enter the user code and press
the programming button. the programming button.
The manufacturer warrants the product to be free from defects in material and workmanship for a period of 12
months from the original date of purchase. If you discover a defect in the product covered by this warranty, we will
While the door is locked, you hear the While the door is locked, you hear the
(1) The depth of the latch (1) The depth of the latch
repair or replace the item at our option using new or refurbished components.
latch bolt coming out when you press latch bolt coming out when you press
bolt hole is insufficient. bolt hole is insufficient.
EXCLUSIONS
the Programming button to lock the the Programming button to lock the
This warranty covers defects in manufacturing discovered while using the products as recommended by the
door; however, three short beeps are door; however, three short beeps are
(2) The latch bolt is not (2) The latch bolt is not
manufacturer rather than occurred by the act of God, and damages caused by misuse, abuse, and unauthorized
emitted. Conversely, while the door is emitted. Conversely, while the door is
aimed at the opening aimed at the opening
modification.
open, no beeps are emitted when open, no beeps are emitted when
of the strike. of the strike.
LIMITED LIABILITY
locking the latch bolt. locking the latch bolt.
The manufacturer will not be held liable for incidental or consequential losses or damages from any act of God.
Warranty Warranty
WARRANTY
The retailer of this product hereby warrants, subject to the conditions set forth below, that it will either repair or replace, at its
option, this product if it proves to be defective by reason of improper workmanship or materials within the original purchaser's
The manufacturer warrants the product to be free from defects in material and workmanship for a period of 12 The manufacturer warrants the product to be free from defects in material and workmanship for a period of 12
limited time. In order to obtain repairs or replacement under this limited warranty you must bring this product to the retailer's
store in which you bought it. Original purchaser: This limited warranty is limited to the original purchaser at retail of this product
months from the original date of purchase. If you discover a defect in the product covered by this warranty, we will months from the original date of purchase. If you discover a defect in the product covered by this warranty, we will
from retailer. Limited 25 years mechanical and 1 year electronic warranty. Except to the extent prohibited by applicable law, no
repair or replace the item at our option using new or refurbished components. repair or replace the item at our option using new or refurbished components.
other warranties, whether express or implied, including the warranties of merchantability and tness for a particular purpose,
EXCLUSIONS EXCLUSIONS shall apply to this product. Under no circumstances shall retailer be liable for consequential or incidental damages in connection
with this product. To the extent retailer is prohibited by applicable law from excluding implied warranties, the duration of such
This warranty covers defects in manufacturing discovered while using the products as recommended by the This warranty covers defects in manufacturing discovered while using the products as recommended by the
implied warranties which are not excludable shall be the original purchaser's limited warranty time. Some states do not allow
manufacturer rather than occurred by the act of God, and damages caused by misuse, abuse, and unauthorized manufacturer rather than occurred by the act of God, and damages caused by misuse, abuse, and unauthorized
the limitation on how long an implied warranty lasts, so the above limitation on the duration of implied warranties which are
modification. not excludable, if any, may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential modification.
damages, so the above limitation or exclusion of incidental or consequential damages may not apply to you. Retailer neither
LIMITED LIABILITY LIMITED LIABILITY
assumes nor authorizes any representative or other person to assume for it any obligation or liability other than such as
The manufacturer will not be held liable for incidental or consequential losses or damages from any act of God. The manufacturer will not be held liable for incidental or consequential losses or damages from any act of God.
is expressly set forth herein. This limited warranty gives you specic legal rights, and you may also have other rights which
vary from state to state. For warranty service, please call 1-877-442-8347, 8:00 a.m. - 8:00 p.m., EST, Monday - Friday.
R
R
Reset
button
R R
CORRECTIVE ACTION
R R
Reset Reset
button button
CORRECTIVE ACTION CORRECTIVE ACTION
Refer to step1. Refer to step1.
step 1)
Check to see if the battery polarities Check to see if the battery polarities
have been reversed or if the battery is have been reversed or if the battery is
dead. dead.
If so, re-install or change the battery. If so, re-install or change the battery.
If not, please check to see if the cable is If not, please check to see if the cable is
properly connected. properly connected.
Press the R button to restore the system Press the R button to restore the system
to factory default setting and re-execute to factory default setting and re-execute
door-handing identifying process door-handing identifying process
( Refer to ( Refer to step 1) step 1)
Replace with new alkaline batteries. Replace with new alkaline batteries.
First, take out one battery, then press First, take out one battery, then press
any button on the front panel for electric any button on the front panel for electric
discharge, and put the battery back in. discharge, and put the battery back in.
The latch bolt will automatically The latch bolt will automatically
re-detect its position. re-detect its position.
Note: If the latch gets stuck frequently, Note: If the latch gets stuck frequently,
please check and fix the alignment of please check and fix the alignment of
the deadbolt latch & strike plate. the deadbolt latch & strike plate.
Unlock the door with the key and Unlock the door with the key and
re-program the unit. re-program the unit.
If the problem persists, call our customer If the problem persists, call our customer
service department. service department.
(1) Dig the latch bolt hole for the strike (1) Dig the latch bolt hole for the strike
deeper. The minimum depth is 1 in. deeper. The minimum depth is 1 in.
(2.5 cm). (2.5 cm).
(2) Adjust the strike to the appropriate (2) Adjust the strike to the appropriate
position. position.
Printed in Taiwan