Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Speedaire® Operating Instructions and Parts Manual
Speedaire
9. If hose stopper adjustment is required,
pull hose from reel and allow latching at
desired storage length. Loosen stopper
bolts and slide stopper to a position
close to the hose guide roller bracket.
Tighten stopper bolts, and unlatch the
reel.
Operation
1. Check reel for correct operation by
slowly pulling out the hose. A "clicking"
noise will be heard three times every
half revolution of the drum.
2. To latch the reel, pull out the hose and
allow it to retract after hearing the first,
second, or third "click".
3. To unlatch the reel, slowly pull out the
hose until the "clicking" noise stops
about ½ of a revolution, and then let
the hose retract until the hose stop rests
against the hose guide.
To avoid damage to
the reel or personal injury always hold on
to the hose while it is rewinding.
4. Periodically check the hose condition for
wear or damage and check the swivel
fitting for leakage. Replace any worn,
damaged, or leaking parts.
Maintenance and Repair
Spring Tension Adjustment
If reel will not wind hose up completely it
may be necessary to adjust the tension of
the spring.
1. Pull out approximately 6 ft. (2 m) of hose
and allow the drum to latch.
2. Remove hose stopper from hose and
feed hose back through guide.
3. Wrap the pulled hose one time around
the drum to increase tension or unwrap
hose one time to decrease tension.
4. Reinsert hose through guide and install
hose stopper onto hose end. Securely
tighten hose stopper bolts.
5. Unlatch the drum and check tension. Pull
hose from reel and adjust stopper
position if necessary.
The spring tension can
spin the reel quickly and with force.
Industrial Hose Reel 1/4, 3/8"
®
FIGURE 1 Reel Mounting Positions
Hose Guide Roller Bracket Bolts
Wall
Swivel Seal Replacement
1. Turn off air supply and carefully release
pressure in hose. Disconnect supply line
from swivel inlet.
2. Remove swivel assembly from reel axle.
3. Remove retainer from swivel and take
apart. NOTE: You may want to remove
swivel from reel hose end but this is not
necessary unless a new swivel is being
installed.
4. Replace the seals and reassemble swivel.
5. Use thread sealant on swivel thread
fitting, reconnect the swivel thread
fitting with axle.
6. Reconnect inlet supply line.
Hose Replacement
1. Turn off air supply to reel and carefully
release pressure in hose.
2. Securely stabilize the reel by mounting
or clamping to work surface.
3. Pull out all the old hose and lock the reel
in this position.
securely locked by letting ratchet teeth
engage.
Replacement of Hose (continued)
4. Remove the two hose clamps connecting
the hose to the reel.
5. Carefully disconnect hose from the
swivel joint on the side of the reel and
discard old hose.
6. Feed new hose through guide and
opening in drum, use sealant and
connect to swivel. Reuse hose clamps on
inside and outside of drum flange to
reconnect hose.
7. Securely install stopper on other end of
hose in the same position as before.
Adjustments can be made later.
red arrow label on reel. It shows the reel is
rewinding.
Floor
8. Carefully release the drum latch, and
NOTE: Final spring adjustment is
accomplished by adding or removing wraps
of hose around the drum. (Refer to Page 3
- Spring Tension Adjustment).
not serviceable. Do not remove spring
cover.
PREVENTATIVE MAINTENANCE
Inspect normal wear items (plastic rollers,
rubber stop, etc.) periodically for possible
replacement.
LIMITED ONE YEAR WARRANTY
Should a Speedaire Hose Reel fail to
perform satisfactorily due to defect or poor
workmanship within one year of purchase,
return it to your place of purchase and it
will be replaced or repaired free of charge.
Incidental or consequential damages
Make sure reel drum is
are excluded from this warranty.
FIGURE 2 - Base Template
Notice direction of the
2
2CUA3/2CUA5/2CUA7
Ceiling
while securely holding hose, slowly allow
the hose to wind onto the reel.
The rewind spring is
Template is not drawn to scale
Publicidad
Tabla de contenido
