Maintenance Instructions - Sunny Health & Fitness SF-T1407M Manual Del Usuario

IMPORTANT NOTE:
You will need to lubricate your treadmill before the first use!
RUNNING BELT & TREADMILL LUBRICANT:
Lubricating the Running Board (No. 26) and Running Belt (No. 2) is essential as the friction affects the life span and
operations of the treadmill. Inspect the Running Board (No. 26) and Running Belt (No. 2) regularly. If you find any
wear on the Running Board (No. 26), please contact us at support@sunnyhealthfitness.com.
1. Raise the Running Belt (No. 2) up on one side, apply lubricant to the Running Board (No. 26). Using a rag,
thoroughly wipe the lubricant over the Running Board (No. 26) and repeat the same process for the other side.
2. The moving parts should turn freely and quietly. Abnormal moving parts will affect the safety of the treadmill.
Checking and tightening bolts in each part of the treadmill regularly is very important.
3. To better maintain the treadmill and prolong its life, it is suggested that maintenance be done on a regular and
consistent basis.
4. DO NOT LOOSEN OR MAKE ANY ADJUSTMENTS TO THE RUNNING BELT WHILE APPLYING LUBRICANT. A
loose Running Belt (No. 2) will result in the runner sliding off when in use, while too tight of a Running Belt (No. 2)
will create more friction between the roller and Running Belt (No. 2). The most suitable tightness for the Running
Belt (No. 2) is pulled out 50-75mm from the Running Board (No. 26).
General cleaning will help to prolong the life and improve performance of your treadmill. Keep the unit clean and
maintained by dusting the components on a regular basis. Cleaning the two exposed sides of the Running Belt (No. 2)
will prevent dust from accumulating underneath. Keep your running shoes clean so that dirt from the shoes does not
wear the Running Board (No. 26) and Running Belt (No. 2). Clean the surface of the Running Belt (No. 2) using a
clean damp cloth.
ADJUSTING THE RUNNING BELT:
1. If the Running Belt (No. 2) moves to the right, turn the Adjustable Bolt (No. 40) on the right side ¼ turn clockwise,
then turn the left Adjustable Bolt (No. 40) ¼ turn counter-clockwise. If the Running Belt (No. 2) does not move,
repeat this step until it centers.
2. If the Running Belt (No. 2) moves to the left, turn the Adjustable Bolt (No. 40) on the left side ¼ of a circle
counter-clockwise, then turn the right Adjustable Bolt (No. 40) ¼ turn clockwise. If the Running Belt (No. 2) does
not move, repeat this step until it centers.
3. Over time the Running Belt (No. 2) will loosen. To tighten the Running Belt (No. 2), turn both the left & right
Adjustable Bolts (No. 40) one full turn clockwise. Check the tension of the Running Belt (No. 2). Continue this
process until Running Belt (No. 2) is at the correct tension. Make sure to adjust both sides equally to ensure even
alignment.
During exercise, if the Running Belt (No. 2) feels loose, you can tighten the Running Belt (No. 2) a little by rotating
both Adjustable Bolts (No. 40) at the same time ¼ turn clockwise. If the Running Belt (No. 2) feels too tight, you can
loosen the Running Belt (No. 2) by rotating both Adjustable Bolts (No. 40) at the same time ¼ turn
counter-clockwise. You can repeat this adjustment to obtain your desired belt tightness.
LUBRICATING THE TREADMILL
Light user (less than 3 hours/ week)
Medium user (3-5 hours/ week)
Heavy user (more than 5 hours/ week)

MAINTENANCE INSTRUCTIONS

The following time table is recommended:
9
once a year
every six months
every three months