DeLonghi PAC EM Manual De Instrucciones página 10

DESCRIPTION OF THE REMOTE CONTROL
D1. ON/STAND-BY button
D2. MODE button
D3. Fan speed selection button
D4. Increase button
D5. Decrease button
D6. Timer button
D
C11
C15
D1
C8
C11
C10
C15
D5
C8
C14
C11
C10
C15
C8
C14
C10
TURNING THE APPLIANCE ON/OFF USING THE
C3
REMOTE CONTROL
C14
• Plug into the outlet.
C2
• Press the ON/STAND-BY button
C3
the air conditioner starts operating in the same mode as
when it was turned off.
C2
• Press the ON/STAND-BY button
C3
appliance off.
Please note: Never switch the appliance off by removing the plug.
C2
Always switch it off by pressing the
and waiting few minutes before removing the plug. The appliance
will only perform the standard checks if the appliance is switched
off following this process. Pressing any button the remote control
will automatically sync to the unit itself and whatever appears
on the remote control display will now also appear on the unit
display.
SELECTING THE OPERATING MODES
The operating modes available on the remote control through
the MODE button (D2) correspond to those on the appliance
control panel (C).
SELECTING THE TEMPERATURES
In air conditioning mode press (D4) or
the desired temperature.
SELECTING THE AIR FLOW
In air conditioning and fan modes press
C5
C6
C7
D2
C5
C9
C6
D3
C7
C12
D4
C5
C9
C6
D6
C13
C7
C12
C9
C13
C12
C4
C13
C1
(D1). When turned on,
C4
C1
(D1) again to switch the
C4
C1
ON/STAND-BY button (D1)
(D5) button to select
button (D3)
10
to select the desired air flow.
The air flows available are:
Minimum air flow: when maximum quiet operation
is desired.
Medium air flow: when the noise level needs to be
low but with a good comfort level.
Maximum air flow: for maximum performance.
Auto air flow: the appliance automatically chooses
the air flow based on the temperature selected and the
environmental conditions. This selection is only avail-
able in air conditioning mode.
SELECTING THE TEMPERATURE SCALE
The temperature can be displayed in °C or °F. To change the tem-
perature unit of measure select the air conditioning mode then
press both the decrease
about 3 seconds.
SETTING THE TIMER
The timer allows the delayed start up or shut down of the appli-
ance. This function will prevent wasting electricity by optimizing
the operating periods.
How to program delayed shut down
C11
• While the appliance is on in any operating mode, delayed
shut down can be programmed.
C15
• Press the timer button
C8
played and the hours light up.
• Press the (D5) and
C10
number of hours to shut down appears on the display.
A few seconds after the timer is set, the setting is acquired, the
C14
display shows the operating mode and the timer symbol stays lit.
C11
Once the set time is elapsed, the air conditioner goes into standby.
C15
To cancel the timer program, press the
C8
twice. The timer indicator will go off.
C10
How to program delayed start up
C11
C3
• Plug in the appliance and set to standby.
C14
C15
• Press the timer button
C8
C2
played and the hours light up.
C10
• Press the (D5) and
number of hours to start up appears. Start up can be pro-
grammed at anytime within the next 24 hours.
C14
C11
When the set time is elapsed, the appliance will start to operate
C3
in the same operating mode that was previously set.
C15
To cancel the timer program, press the
C8
C2
twice. The timer indicator will go off.
C10
Note:
C3
•
This equipment has been tested and found to comply with the
C14
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protec-
C2
(D5) and increase (D4) keys for
C5
C6
C7
(D6), the timer symbol is dis-
C9
(D4) buttons until the desired
C12
C13
timer button (D6)
C5
C4
C6
C7
(D6), the timer symbol is dis-
C9
C1
(D4) buttons until the desired
C12
C13
timer button (D6)
C4
C1
C5
C6
C7
C9
C12
C13
C5
C4
C6
C7
C9
C1
C12
C13