CompuSTAR Firstech FT-KP2 Manual De Operación Y Programación

Programming &
Operation Manual
White
CM-X
CM7 Series
CM-DC3
Gray
CM-900
CM-900AS
CM2400
Compatibility (ENGLISH)
Red LED
CM-X, CM7 Series, and CM-DC3 (Make sure firmware is updated)
Green LED
Connect to the controller RPS port (white 4-pin).
Connect to the controller UART port (gray 4-pin), using ' ANT-Adapt-
er-KP2' (included in kit).
sensitivity.
sensitivity.
Mounting & Installation
1) The KP2 touchpad module should be mounted on the front
windshield on the interior, driver's side. Thoroughly clean and dry the
intended surface.
2) Connect the 4-pin harness prior to mounting.
3) Remove the protective film on the KP2 touchpad module, exposing
the adhesive.
4) Firmly adhere the KP2 touchpad module to the interior of the
windshield at your desired placement. Hold the module in place for
conds.
KP2 Programming and Passcode Reset
Via Touchpad Module
1) Using your vehicle's key, turn the ignition to the ON position. You do
not need to start the engine. Then, open the driver's side door and
leave it open.
2) Press and hold the LOCK button the KP2 touchpad module for 2.5
seconds.
3) If your system has a siren, it will lightly chirp and the red LED will
blink, indicating programming mode.
4) Firmly tap in the first digit of your new passcode. The LED will blink
green when input is received, and then red (with siren chirp) when it
is safe to enter the next digit. Repeat this process until you have
entered all 4/6 digits.
5) Once you have entered all of the digits, please wait until you hear
another siren chirp and see a single parking light flash. This indicates
(ANT-Adapter-KP2)
that programming was complete and successful.
a) If programming is incomplete and/or fails, you will receive three
siren chirps and three parking light flashes. If this occurs, turn your
-X: Feature Option 3-16 to Setting 2 (KP2), 4-15 for sensitivity.
Feature Option 3-16 to Setting 2 (KP2), 4-15 for sensitivity.
Feature Option 3-16 to Setting 2 (KP2).
ted Operation
ke sure firmware is updated)
/AS: Feature Option 4-11 to Setting 3 (KP2), 4-15 for
Featur to Se
engine back OFF, close the driver's side door, and re-attempt steps
#1 through #5.
Via DroneMobile App
If your KP-2 touchpad module is installed with a Drone KL1 KeyLocker
system, you can now manage your passcode(s) from the DroneMobile
App. Please visit https://help.dronemobile.com and search "KP2".
KP-2 User Guide (Arming + Disarming)
Arm/Lock - To arm and lock your vehicle's doors, hold down
the LOCK button for 2.5 seconds - do not press any number.
One chirp/honk and One parking light flash will confirming
lock/arm.
for
Disarm/Unlock - To disarm and unlock your vehicle's doors,
hold down the LOCK button for 2.5 seconds, then enter your
passcode. NOTE: please press each digit firmly and pause for 1
seconds for two chirps/honks and two parking light flashes,
confirming unlock.
Compatibilité (FRANÇAIS)
CM-X, CM7 Series, et CM-DC3 (assurez-vous que le micrologiciel est mis à
jour)
Connecter au port RPS du contrôleur (blanc à quatre broches).
-X : Option de fonction 3-16 au réglage 2 (KP2), 4-15 pour la
sensibilité.
sensibilité.
Fonctionnement limité
e
à jour)
Connectez-vous au port UART du contrôleur (gris à quatre broches), en
utilisant 'ANT-Adapter-KP2' (inclus dans le trousse).
/AS : Option de fonction 4-11 au réglage 3 (KP2), 4-15
pour la sensibilité.
sensibilité.
Montage et installation
1) Le module du pavé tactile KP-2 doit être monté sur le pare-brise
fonction 3-16 au réglage 2 (KP2), 4-15 pour la
fonction 3-16 au réglage 2 (KP2).
rez-vous que le micrologiciel est mis
f réglag