Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Grill Lighting Instructions
1.
Before each use, check all hoses for cracks, nicks, cuts,
burns or abrasions. If a hose is damaged in any way, do
not use your grill before replacing the hose with an
authorized part from the Parts List. Also make sure all
gas supply connections are securely tightened.
2.
Familiarize yourself with the safety and Use and Care
instructions in this manual. Do not smoke while lighting
grill or checking gas supply connections.
3.
Be sure the LP Gas tank is filled.
Open the Grill Lid during lighting.
4.
5.
Check that the end of each Burner Tube is properly
located over each Valve Orifice (see page 25).
WARNING
!
Failure to replace a faulty hose, secure gas supply
connections or to open the Lid before proceeding
to the Lighting Procedures could result in a fire
or explosion that could cause serious bodily injury,
death, or property damage.
6.
Set Control Knobs to OFF and open the LP Gas
tank valve
SLOWLY 1/4 of a turn.
OFF
Push and turn the Main Burner Control Knob to
ON/
. Always light the LEFT Main Burner first.
Press the electric ignitor 3 to 4 seconds to light the
burner.
ON/
LOW
7.
If ignition does not occur in 5 seconds, turn gas off
at source and turn Control Knobs OFF. Wait at least
5 minutes for gas to clear, then retry. If your grill still
fails to light turn the burner Control Knob(s) and gas
source OFF and conduct a leak test of ALL gas
connections and gas sources as explained in the
Use and Care section of this manual. If no leaks are
detected, wait 5 minutes for any gas to clear and
repeat the lighting procedure.
8.
After one Burner is lit, turn the tank valve SLOWLY
one more 1/4 of a turn for 1/2 of one complete turn.
9.
Repeat steps to light each burner individually. Turn
other burners to ON/
the fuel source.
USE AND CARE INSTRUCTIONS
!
Open LP
gas tank
OFF
to light as you move towards
Burner Control Knobs on Control Panel
Grill
Main Burner
Infrared Burner Lighting Instructions
1.
Follow steps 1 through 6 of the Grill Lighting
Instructions.
Then, push and turn the Infrared Burner Control Knob
2.
to ON/
and press the electric ignitor 3 to 4 seconds
to light the burner. Hold the knob in 10 seconds be-
fore releasing. If ignition does not occur follow step 7
before retrying.
ON/
3.
After the Infrared Burners is lit it will reach cooking
temperature quickly. The orange/red glow will even
out within minutes.
Back Burner Lighting Instructions
1.
Follow steps 1 through 6 of the Grill Lighting
Instructions.
2.
Then, push and turn the Back Burner Control Knob
to ON/
and press the electric ignitor 3 to 4
seconds to light the Burner. Hold the knob in 10
seconds before releasing. If ignition does not occur
follow step 7 before retrying.
ON/
3.
After the Back Burner is lit it will reach cooking
temperature quickly. The orange/red glow will
even out within minutes.
Side Burner Lighting Instructions
1.
Follow steps 1 through 5 of the Grill Lighting
Instructions.
Open Side Burner Lid.
2.
3.
Set Control Knob to OFF and open the LP Gas tank
valve SLOWLY 1/4 of a turn.
4.
Push and turn the Control Knob to ON/
spark ignitor will light the Burner automatically.
5.
You may have to pusk and turn the Control Knob up to
3 to 4 times to light.
6.
If ignition does not occur, turn the burner Control Knob
and gas source OFF and conduct a leak test of ALL
gas connections and fuel sources. If no leaks are
detected, wait 5 minutes for any gas to clear and re-
peat the lighting procedure.
IMPORTANT: Do not use the Back Burner and
Main Burners at the same time. Backburner is
for Rotisserie Cooking only.
20
Back
Infrared
Burner
Burner
OFF
OFF
. The built
Publicidad
Tabla de contenido
