Transport And Handling Instructions; Instructions For Use - Volpi ELETTROLITHUM 10PTBLIT Manual De Uso

5. TRANSPORT AND HANDLING INSTRUCTIONS

The transport of the sprayer must be effected using all the necessary cautions in order to avoid damages.
The sprayer must not be placed on or under any other products during transport and storing.
When transporting the sprayer please make sure the switch on/off is always off.
When moving the sprayer it is recommended to avoid bumps which could cause damage to the product.

6. INSTRUCTIONS FOR USE

6.1. SETTING OF THE SPRAYER
Fix the hooks (FE70/1) at the bottom of the shoulder straps (picture 3) (10PTELIT, 10PTCLIT).
Screw the extension (189TPE) on the handle (10K5) (10PTELIT, 10PTCLIT).
Check that the status of the battery is good (see Prg. 6.2), this operation which ensures the maximum
operation of the sprayer must be done every time you reuse the pump after a period of inactivity.
However, at least every four months of inactivity, the battery must be fully charged (see Prg. 6.2).
6.2. FILLING OF THE SPRAYER TANK
Prepare the solution in a specific container.
Unscrew the cap (92/2) of the tank and pour the prepared solution (picture 4) through the filter (78/3).
Carefully screw the cap.
WARNING:
Do not prepare the solution in the sprayer tank but always in a separate container.
Do not ever pour the solution into the tank without the use of the filter.
6.3. OPERATION AND POSITIONING OF THE SPRAYER
Link one of the hooks (FE70/1) in its special housing (picture 5) placed in the lower part of the base
(98/61), slip one arm in the shoulder-strap and put the sprayer on one shoulder, then with the other hand
seize the free strap and hook it to the base after passing it over the shoulder. When you put the sprayer
away make the opposite operation (10PTELIT, 10PTCLIT).
To activate the sprayer first turn on the general switch then turn the handle lever to start the sprayer
(10PTELIT, 10PTCLIT). For sprayer 10PTBLIT, you have to switch it working directly with the general
switch.
WARNING: Never let the sprayer work when the tank is empty.
This sprayer (10PTELIT, 10PTCLIT) is supplied with a manual pressure regulator (10/8) and with an
adjustable cone nozzle (928) (picture 7). To regulate the pressure variation rotate the handle (fig. 1A) of
the regulator; when screwing it tight you get the maximum pressure and by unscrewing it the pressure
will be released. The 10PTBLIT sprayer work with fixed pressure.
6.4. OPERATIONS TO BE CARRIED OUT AT TERMINATION OF WORK
When finishing work, pour the remaining liquid in a specific container and carefully rinse the internal of the tank and the hose
letting it flow through the lance with clean cold water.
Check that the water used for rinsing has completely come out. Turn off the general on/off switch (0-1) after every use.
In case of long inactivity of the machine, after having cleaned the tank, remove, clean and put back the filter inside the tank
(98/5) and the one in the rear part of the handle. Wear protective clothing and equipment during these activities.
Clean the handle using a wet rag without dipping it into water.
Clean the sprayer from foreign materials such as deposits or other things which could damage it.
WARNING: Do not disperse the rinsing water neither the remaining solution in the environment; it is recommended to pour
all these liquids in specific drains, appositive for water purification and drainage.
Switch off the general switch (0-1) after every use.
Keep the sprayer out of reach from children and protected from sunrays and cold temperatures.
DAVIDE E LUIGI VOLPI S.p.A. - Via San Rocco,10 - 46040 CASALROMANO (MN) - ITALY
Davide e Luigi Volpi S.p.A.
Via San Rocco,10 – 46040 Casalromano (MN) – Italy
Tel. +39 0376.76009 - 76012 Fax. +39 0376.76408
www.volpioriginale.it
e-mail: commerciale@volpioriginale.it
– export@volpioriginale.it
YLB10ALIT_3 Libretto d'uso Elettrolithium
pag. 13 di 32