Can Ices-3 (B)/Nmb-3(B); Contact; Appendix 1: Steps For Swelling Water Bullets; Appendix 2: Replacement Of Adapter Pad - Ninebot Mecha Kit Manual Del Usuario

correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
Cet équipement est conforme aux limites d'exposition aux radiations de la IC définies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps.
Industry Canada (IC) Compliance Statement for Canada
This device complies with Industry Canada license-exempt RSS standard (s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.

CAN ICES-3 (B)/NMB-3(B)

"Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement."
Neither Segway Inc. nor Ninebot is responsible for any changes or modifications not expressly approved by Segway Inc. or
Ninebot. Such modifications could void the user's authority to operate the equipment.
FCC ID:2ALS8-PS0004
IC:22636-PS0004

12. Contact

Contact us if you experience issues relating to riding, maintenance and safety, or errors/faults with your Mecha Kit.
Americas:
Segway Inc.
P.O. BOX 3925, Alhambra, California, USA, 91803
Toll Free: 1-888-523-5583
Fax: 1-603-222-6002
Technical Support Email: technicalsupport@segway.com
Website: www.segway.com
Have your Mecha Kit serial number on hand when contacting Segway.
You can find your serial number on the underside of your Mecha Kit or in the app under More Settings > Basic Information.
24

Appendix 1: Steps for swelling water bullets

a. Take out about 900 water bullets (roughly one cap of the water bullet bottle) and pour them into a container such as a
water basin.
b. Pour 0.66 US gal of purified water in the basin at room temperature.
c. Soak for over 4 hours.
d. Use water bullet bottles to store and carry soaked water bullets.
* Due to the varying properties of tap water and mineral water, water bullets may not be soaked to the specified sizes. When
the water is not at optimal conditions, please use purified water at room temperature or appropriately extend the soaking
time. Water bullets fully soaked should be 7–8 mm in size. When soaking for the first time, you may not be able to
determine the exact number of water bullets required. It is recommended to use open containers such as water basins be
used for soaking.
Tip: The bullet case located on each side can load about 450 water bullets.
0.66 US gal
4 hours

Appendix 2: Replacement of adapter pad

The original adapter pad (for Ninebot S) does not apply to Ninebot S Kids.
If your product is a Ninebot S Kids, you need to make a replacement using
the S Kids adapter pad.
Steps:
a. Unscrew the four screws under the adapter pad with a hex wrench.
b. Replace the S Kids adapter pad, align the holes, and tighten the screws.
Note: The strap holes should face forward.

Appendix 3: Troubleshooting for a blocked launch tube

The launch tube may be blocked by water bullet fragments or oversized water bullets, and water bullets cannot be launched.
Solution: Remove the remaining water bullets in the bullet case and leave the Mecha Kit to dry for more than 1 day. After the
moisture evaporates, water bullets will shrink, which will resolve the issue.
To avoid damaging the Mecha Kit, do not forcefully unclog the launch tube with sharp tools.
25