Porcher L'Expression II 97520 Instrucciones De Instalación Cuidado Y Mantenimiento

INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
L'Expression II 1.6 GPF One-Piece Toilet Model 97520
Epic 1.6 GPF One-Piece Toilet Model 97720
Thank you for selecting Porcher - the benchmark of fine quality for over 100 years. To ensure this product
is installed properly, please read these instructions carefully before you begin. (Certain installations may require
professional help.) Also be sure your installation conforms to local codes.
!
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver
Hacksaw Wax Ring/Gasket
1
REMOVE OLD TOILET
a. Close toilet supply valve and flush tank
completely. Towel or sponge remaining
water from tank and bowl.
b. Disconnect and remove supply line.
NOTE: If replacing valve, first shut off
main water supply!
c. Remove old mounting hardware, remove
toilet and plug floor waste
opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean
away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and
level before new toilet is installed!
MODEL A
172mm
97520
6-3/4"
172mm
97720
6-3/4"
3
INSTALL CLOSET BOLTS
Install closet bolts in
flange channel, turn
90 ° , and slide into
place 6" (152 mm)
apart and parallel
to wall.
CLOSET
BOLTS
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f P o r c h e r
© P o r c h e r 2 0 0 8
Adjustable Wrench
Flexible Supply Tube
B C D
190mm 313mm 403mm
7-1/2" 12-3/8" 15-7/8"
150mm 370mm 425mm
5-7/8" 14-5/8" 16-3/4"
CLOSET
FLANGE
A
Sealant
Closet Bolts
2
ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange centerline must be as listed below:
FINISHED WALL
G
19 ± 6mm
(3/4 ± 1/4)
A
C/L OF SEAT
POST HOLES
140mm (5-1/2)
CENTERS
J
B
305mm
C/L OF OUTLET
(12)
DIMENSIONS
E F
784mm 325mm 758mm
30-3/4" 12-13/16"
796mm 320mm 760mm
31-5/16" 12-5/8" 29-15/16"
4
INSTALL TOILET SEAT
a. Remove the hinge covers. Place
bolt through hinge cover hole and
gasket, loosely retain with nut.
b. Align the hinge assembly with
the seat mounting holes, insert and
tighten until snug. Snap hinge
covers into place.
For additional help see instructions
supplied with seat.
Tape Measure
Carpenters Level
H
SUPPLY
AS
REQ'D
K
222mm
(8-3/4)
C 152mm
G H J
465mm 70mm
29-5/8" 18-5/16" 2-3/4"
465mm 70mm
18-5/16" 2-3/4"
D
L
E
FINISHED
FLOOR
(6)
F
K L
404mm 356mm
15-7/8" 14"
385mm 350mm
15-1/4" 13-3/4"
7 3 0 1 1 9 6 - 1 0 0 Re v . A