Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

1. INPUT LEVEL CONTROLS:
corresponding channels.
2. MASTER LEVEL CONTROL:
before sending to the output connectors.
3. MASTER OUTPUT INDICATORS:
Master level control will light up when the output signal exceeds
-40dB indicating that a signal is present. The red LED indicator will light
up when the output signal reaches high peaks with the potential of causing
distortion. In the event the Peak LED lights up, Phonic suggests reducing
the Master output level.
4. BASS CONTROL:
Turning to the right will increase the response
of low-frequency signals (100 Hz) in your main audio signal. Turning to
the left will decrease the response of low-frequency signals.
5. TREBLE CONTROL:
Turning to the right will increase the response
of high-frequency signals (10 kHz) in your main audio signal. Turning to the
left will decrease the response of high-frequency signals.
6. CHIME & ALERT TONES:
These two buttons will send an alert or
an announce tone through to the speakers. The alert button can also be
used to activate a siren, the length of which will be 2 minutes and 30
seconds. Pushing the Alert button a second time will disengage the
siren. The ''announce' button will active a 3 second 'do mi so do' tone to
indicate an announcement. Activating either of these tones will cut out
all music and other input sources.
7. POWER BUTTON & INDICATOR:
mixer/amplifier on. When the unit is turned on, the LED indicator will
illuminate to indicate as such. Be sure that the mixer amplifier is turned
on after all other input sources.
8. INPUT AMP CONFIGURATION DIP SWITCHES:
switches have a number of different functions. See reverse for details.
9. INPUT 1 TERMINAL:
This is a 5-pin Phoenix-type connection
with 3 pins for balanced input signals and 2 connectors for priority
push-to-talk button connection. The input accepts direct connection of line
or microphone inputs as selected by the mic/line DIP switch.
10. INPUT 1 VOX THRESHOLD CONTROL:
level at which the Input 1 signal should be before other signals are
muted. his only works when the CH1 VOX DIP switch is turned on.
17
16
19
20
18
1
Controls in the input level control for the
This controls the final output level
The green LED above the
This button turns the GA
These DIP
This control adjusts the
9
15
http://www.phonic.com
GA6120 / GA6240 EASY MANUAL
6
4
11. XLR INPUTS:
Channel 2 on the GA6120 and GA6240 offers
users with an XLR microphone input, ideal for input of microphones.
12. ¼" INPUTS:
The GA6120 and GA6240 offer unbalanced ¼"
phone jack input connectors input channels 2, 4 and 5.
13. 1/8" MINI-STEREO INPUTS:
GA6240 also offers 1/8" mini-stereo input connectors, similar to
those used on laptops, iPods and other MP3 players.
14. RCA INPUTS:
These inputs accept stereo unbalanced line-
level RCA input signals. The input signals received through these
connectors are summed.
15. ZONE 2 / MOH OUTPUT AND CONTROL:
type connector provides two different output possibilities. The 8 ohm side
is for 1W output to external speakers, while the 600 ohm connectors are
for connecting private branch exchange (PBX) telephone systems for
on-hold music. For further info on wiring, see the Output Wiring section.
16. LINK OUTPUT:
the pre-fader main output signal of the amplifier and sent it to
external devices.
17. LINK INPUT:
This unbalanced ¼" phone jack input allows users
to incorporate external signals directly into the main mix.
18. AMPLIFIER OUTPUT:
terminal. Connections available include COM (common), 70V, 100V and
8 ohms. These input connections can accept terminal forks up to 10 AWG.
For further info on wiring, see the Output Wiring section.
19. POWER CABLE:
Please connect the cable to a suitable AC power outlet. While the GA
series offers a universal power supply, be sure to check local voltage
levels before connecting the unit to ensure they correspond.
20. 24V BATTERY INPUT & CHARGING SWITCH:
plug input connectors can be connected to the positive and negative
terminals of a 24V DC power source. This allows the unit to function even
in the vent of power outages. The switch located above these
connections is used to activated and deactivate the charging circuit. It is
advised not to leave the battery in charge mode when already fully
charged.
8
10
11
12
14
13
3
2
5
Channel 6 of the GA6120 and
This 4-pin Phoenix-
This unbalanced ¼" phone jack output takes
Speakers can be connected to this output
The GA series' has a preinstalled power cable.
7
These banana-

Publicidad

loading

Resumen de contenidos para Phonic GA6120

  • Página 1 14. RCA INPUTS: These inputs accept stereo unbalanced line- distortion. In the event the Peak LED lights up, Phonic suggests reducing level RCA input signals. The input signals received through these the Master output level.
  • Página 2 Input 1 to microphone’s push-to-talk function when this is activated. The GA6120 offers 120 Watts of power while the GA6240 offers Activating this switch allows automatic 240 Watts (whether using 8 ohm or direct voltage 70V/100V output). muting when channel 1 input passes CH1 VOX the preset threshold.
  • Página 3 El LED rojo se ilumina si esta dicha señal alcanza niveles estéreo de 3.17 mm, similar a los que se usan para laptops, iPods y otros que podría distorsionar su audio. Si se distorsiona el audio, Phonic le sugiere que reproductores de MP3.
  • Página 4 Se requiere un cableado de clase 2. Permite el enmudecimiento de los canales cuándo el cableado prioritario El GA6120 provee una potencia de 120 Vatios, mientras que el del canal 1 está cerrado. Conecte GA6240 provee una potencia de 240 Vatios (Que utilice 8 Ohmios “CH1 Priority”...

Este manual también es adecuado para:

Ga6240