Publicidad
Idiomas disponibles
Idiomas disponibles
TO MEMORIZE CHANNELS
This TV is equipped with a channel memory feature which allows channels to skip up or down to the
next channel set into memory, skipping over unwanted channels.
Before selecting channels, they must be programmed into the TV's memory. In addition to normal
VHF and UHF channels, this TV can receive up to 113 Cable TV channels. To use this TV with an
antenna, set the TV/CATV menu option to the TV setting. When shipped from the factory, this menu
option is in the CATV setting.
TV/CATV SELECTION
1
Press the MENU button.
2
Press the SET + or – button until the indicator next to "CH SETUP"
begins to flash, then press the ENTER button.
3
Press the SET + or – button until the indicator next to "TV/CATV"
begins to flash.
4
Press the ENTER button to select the TV or CATV mode. The arrow
indicates the selected mode.
5
Press the MENU button twice to return to normal TV viewing.
The chart below is typical of many cable system channel allocations.
CATV CHART
Number on this TV
Corresponding CATV channel
23
24
25
26
27
28
29
30
J
K
L
M
N
O
P
Q
41
42
43
44
45
46
47
48
EE
FF
GG
HH
II
JJ
KK
LL
MM
59
60
61
62
63
64
65
66
WW
AAA
BBB
CCC
DDD
EEE
FFF
GGG
HHH
77
78
79
80
81
82
83
84
RRR
SSS
TTT
UUU
VVV
WWW
XXX
YYY
ZZZ
95
96
97
98
99
100
101
102
103
A-5
A-4
A-3
A-2
A-1
100
101
102
103
113
114
115
116
117
118
119
120
121
113
114
115
116
117
118
119
120
121
NOTE:
Contact your cable company to determine the type of cable system used in your area.
AUTOMATIC CHANNEL MEMORY
1
Press the MENU button.
2
Press the SET + or – button until the indicator next to "CH SETUP"
begins to flash, then press the ENTER button.
3
Press the SET + or – button until the indicator next to "AUTO CH
MEMORY" begins to flash, then press the ENTER button. The TV will
begin memorizing all the channels available in your area. Channel
numbers will remain red until auto memorizing is complete.
4
Press the MENU button twice to return to normal TV viewing.
TO ADD/DELETE CHANNELS
1
Press the MENU button.
2
Press the SET + or – button until the indicator next to "CH SETUP"
begins to flash, then press the ENTER button.
3
Press the SET + or – button until the indicator next to "ADD/
DELETE" begins to flash, then press the ENTER button.
4
Select the desired channels to be added or deleted using the Direct
Channel Selection buttons (10 keys. 0-9), the CH
or the SET + or – button.
5
Press the ENTER button to select ADD or DELETE.
If an unmemorized channel was selected (step 4), the channel
indicator will be red. Press the ENTER button if you wish to ADD the
unmemorized channel. The channel indicator will change from red to
green when a channel is added and the channel will be memorized.
If a memorized channel was selected (step 4), the channel indicator
will be green.
Press the ENTER button if you wish to DELETE the channel from
memory. The channel indicator will change from green to red when a
channel is deleted.
Repeat steps 4 and 5 for each channel to be added or deleted.
6
Press the MENU button three times after adding or deleting all of the
desired channels, to return to normal TV viewing.
ADJUSTING PICTURE
You can adjust the settings for color, sharpness, contrast, brightness and tint.
1
Press the MENU button.
2
Press the SET + or – button until the indicator next to "PICTURE" begins to
flash, then press the ENTER button.
3
Press the ENTER button repeatedly to select the item you want to adjust.
BRIGHTNESS
CONTRAST
COLOR
4
Press the SET + or – button to adjust the setting.
+
BRIGHTNESS
increase brightness
CONTRAST
increase contrast
COLOR
be brilliant color
TINT
be greenish color
makes picture
SHARPNESS
clearer
TO RETURN TO INITIAL SETTING
Press the RESET button while the picture adjusting mode appears on-screen.
CONNECTION TO OTHER EQUIPMENT
The exact arrangement you use to interconnect various video and audio components to the TV is
dependent on the model and features of each component. Check the Owner's Manual provided with
each component for the location of video and audio inputs and outputs.
The connection diagrams below are offered as suggestions. You may need to modify them to
accommodate your particular assortment of components. The diagrams are intended to show
component video and audio interconnections only.
3R00601A E
5
MENU
CH SETUP
PICTURE
LANGUAGE
V-CHIP SET
á
+ / – / ENTER / MENU
TV
CATV
AUTO CH MEMORY
ADD / DELETE
〈 + / – / ENTER / MENU 〉
14
15
16
17
18
19
20
21
A
B
C
D
E
F
G
H
32
33
34
35
36
37
38
39
31
R
S
T
U
V
W
AA
BB
CC
49
50
51
52
53
54
55
56
57
NN
OO
PP
QQ
RR
SS
TT
UU
67
68
69
70
71
72
73
74
75
III
JJJ
KKK
LLL
MMM
NNN
OOO
PPP
85
86
87
88
89
90
91
92
93
86
87
88
89
90
91
92
93
104
105
106
107
108
109
110
111
104
105
106
107
108
109
110
111
122
123
124
125
01
122
123
124
125
5A
MENU
CH SETUP
PICTURE
LANGUAGE
V-CHIP SET
+ / – / ENTER / MENU
á
TV
CATV
AUTO CH MEMORY
ADD / DELETE
〈 + / – / ENTER / MENU 〉
MENU
CH SETUP
PICTURE
LANGUAGE
V-CHIP SET
+ / – / ENTER / MENU
á
TV
CATV
AUTO CH MEMORY
or
button
ADD / DELETE
〈 + / – / ENTER / MENU 〉
ADD
0-9 / + / Ð / ENTER / MENU
á
TINT
SHARPNESS
–
decrease brightness
decrease contrast
be pale color
be reddish color
makes picture softer
TV/AV SELECTION
If you connect the TV to a VCR, camcorder or TV
game, through the audio/video in jacks, use the TV/
AV button to make your selection.
Press the TV/AV button repeatedly to select the
desired mode.
"AUX" will display on the screen for 4 seconds.
AUX
ñ
1. To connect the TV to a VCR
VCR
Front of TV
VIDEO IN AUDIO IN
RESET
To Audio/
Video OUT
VIDEO
(not supplied)
TROUBLESHOOTING GUIDE
22
I
40
Before requesting service, please refer to the following chart for the symptom and possible solution.
DD
58
SYMPTOMS
VV
76
QQQ
TV does not operate.
94
94
112
Poor sound or No sound.
112
Poor picture or No picture.
Poor reception on some
channels.
ñ
Poor color or no color.
Picture wobbles or drifts.
No CATV reception.
Horizontal or diagonal bars
on screen.
No reception above
channel 13.
ñ
No Remote operation.
TV shuts off.
CH 012
Closed - Caption is not
activated.
Display is not shown in
your language.
ñ
DEGAUSSING SYSTEM
This television has a degaussing circuit that will clear up color distortions on the TV screen
that are caused by any excess magnetism which happens to get too close to the TV. This
circuit is designed to operate once when the set is first plugged in. If minor color distortions
are seen in some locations on the screen, please unplug the TV for approximately 15
minutes. When the TV is plugged back in, the degaussing circuit will operate once to clear
up any color distortions. Repeat this procedure any time the TV screen is accidentally
magnetized, or when the TV is moved or relocated.
SPECIFICATIONS
Model
AC Power Input:
AC Power Consumption:
Chassis Construction:
Picture Tube:
Horizontal resolution:
Audio Power Output Rating:
Speaker:
Tuner Type:
Remote Control:
Receiving Channels:
Antenna Input Impedance:
Input:
Dimensions:
Weight:
ACCESSORIES
Remote Control
Telescopic Antenna (MT1134 only)
4/1/04, 8:56 PM
2. To connect the TV to a TV Game
The TV can also be used as a display device for
many video games. However, due to the wide
variety of different types of signal generated by
these devices and subsequent hook-up variations
required, they have not all been included in the
suggested connection diagrams. You'll need to
consult each component's Owner's Manual for
additional information.
To Audio/Video OUT
TV GAME
(not supplied)
3. To connect the TV to a camcorder
To playback from the camcorder, connect the
camcorder to the TV as shown.
To AV OUT
jack
AUDIO
(not supplied)
POSSIBLE SOLUTIONS
• Make sure the power cord is plugged in.
• Try another AC outlet.
• Power is off, check fuse or circuit breaker.
• Unplug unit for an hour, then plug it back in.
• Station or CATV experiencing problems, tune to another station.
• Check sound adjustments (VOLUME and MUTE).
• Check for sources of possible interference.
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
• Check antenna or CATV connections, adjust antenna.
• Check for sources of possible interference.
• Check picture control adjustments.
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
• Station is weak, adjust antenna to receive desired station.
• Check for sources of possible interference.
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
• Check picture control adjustments.
• Check antenna or CATV connections, adjust antenna.
• Check for sources of possible interference.
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
• CATV company is scrambling signal.
• Adjust antenna.
• Check all CATV connections.
• Set TV/CATV menu option to the CATV mode.
• Station or CATV system problems, try another station.
• Check antenna connections, adjust or re-direct antenna.
• Check for sources of possible interference.
• Make sure TV/CATV menu option is in the appropriate mode.
• If using antenna, check UHF antenna connections.
• Batteries are weak, dead or inserted incorrectly.
• Remote is out of range, move closer to TV (within 15 feet).
• Make sure Remote is aimed at sensor.
• Confirm there are no obstructions between the Remote and the TV.
• Make sure the power cord is plugged in.
• No broadcast on station tuned.
• Sleep Timer is set.
• Power interrupted.
• TV station experiencing problems or program tuned is not closed captioned.
Try another channel.
• Check CATV connection or VHF/UHF antenna, reposition or rotate antenna.
• Press TV/CAP/TEXT button to turn on the closed caption decoder.
• Select proper language in the menu options.
MT1134
120V, 60Hz
54 Watts
73 Watts
IC Solid state
13" (measured diagonally)
19" (measured diagonally)
260 lines
1.0 Watts
1.5 Watts
3" Full Range, 8 ohm
181 Channel, Quartz PLL Frequency Synthesized
Infrared, Direct Access, 2 x AAA batteries (not supplied)
VHF
2-13
UHF
14-69
CATV 01-97 (5A)-(A-3)
98-99 (A-2)-(A-1)
14-22 (A)-(I)
23-36 (J)-(W)
37-65 (AA)-(FFF)
66-125 (GGG)-(125)
75 Ohm (VHF/UHF/CATV) Coaxial Input
Video: 1.0 Vp-p 75 ohm
Audio: 300 mV, 47k ohm
14-1/4" (W) x 14-3/16" (D) x
19-3/16" (W) x 18-5/16" (D) x
12-5/8" (H)
16-3/8" (H)
20.9 Ibs
38.6 Ibs
Front of TV
VIDEO IN AUDIO IN
RESET
Front of TV
VIDEO IN AUDIO IN
RESET
MT1194
Publicidad
