Publicidad
Idiomas disponibles
Idiomas disponibles
Locate Horizontal Screw Hole Positions
To locate the horizontal screw hole positions, determine the Door Width by measuring from the outside
edge of the left door stile to the outside edge of the right door stile. Then, determine the Door Panel
Width by measuring from the inside edge of the left door stile to the inside edge of the right door
stile. These two measurements determine the area available to screw the holes for mounting the door
bracket. Locate your Product Assembly number on the chart. Your measurements should be between
one of the minimum and maximum distances on the chart. This will determine how to mount the door
bracket; Side A Facing Center of Door OR Side B Facing Center of Door. Keeping within the minimum
and maximum distances on the chart, mark the horizontal screw hole position on both door stiles so that
the distance from the center of the door to each mark is equal. Note: If cabinet door is constructed
with a center panel, make certain the marks are not positioned in the dado of the door frame. Allow
adequate clearance from edge of dado.
Attach Door Brackets to Cabinet Door
Where the two pencil marks meet is the screw hole location for attaching door bracket to back of
cabinet door. Attach one bracket to door using #6-18 x 5/8" Phillips flat-head sheet metal screws (C) in
the slotted holes of the door bracket. Repeat on other side.
Optional Step
Using 1/16" drill bit, drill pilot holes for inserting screws.
Attach Cabinet Door to Sliding Base Assembly
Insert one #10-24 x 1/4" Phillips pan-head machine screw (N) in
each round hole of door bracket. Turn 2-3 turns. Extend sliding
base assembly (with slide brackets attached) out of cabinet
interior to a comfortable working position. Align the pan-head
screws on door bracket with the keyholes in the slide bracket.
Insert through keyhole and push downward until pan-head screws
are fully seated. If necessary, loosen the pan-head screws slightly
to verify screws are fully seated. Tighten screws.
Adjust Door
Close cabinet door and sliding assembly. Verify that the door
is aligned side to side, up and down, as well as the tilt. To make
side-to-side adjustments, loosen and reposition screws in the
slotted holes of the door bracket. If up and down adjustments are
necessary, loosen and reposition screws in slotted holes of door
bracket. To make tilt adjustments, loosen and reposition rear-most
screws in the bottom of the slide brackets (where attached to
slide members).
Assembly is now complete.
CABINET
CABINET
OPENING
OPENING
7-1/2"
7-1/2"
X
X
Y
Y
OVERLAY
OVERLAY
OVERLAY
OVERLAY
Y + OVERLAY= BOTTOM HOLE LOCATION
Y + OVERLAY= BOTTOM HOLE LOCATION
Y + OVERLAY+ 7-1/2" = TOP HOLE LOCATION
Y + OVERLAY+ 7-1/2" = TOP HOLE LOCATION
X + OVERLAY= DISTANCE FROM SIDE
X + OVERLAY= DISTANCE FROM SIDE
Product
Side "B" Facing
Assembly #
Center of Door
Soft-Close Bottom-Mount Assemblies
Minimum
Distance
BSC9-1-20
8-1/8"
BSC10-1-35
9-1/8"
BSC12-1-50
11-1/8"
BSC12-2-27
11-1/8"
BSC15-1-20
14-1/8"
BSC15-2-20
14-1/8"
BSC15-2-35
14-1/8"
BSC15-3-20
14-1/8"
BSC24-4-27
23-1/8"
Slot to slot widths (located on centerline of door) 1/4-1/2"
overlay.
BACK OF DOOR
BACK OF DOOR
7-1/2"
7-1/2"
Side "B" Facing
Center of Door
Door Width
BACK OF DOOR
Center Panel
Door Panel
Width
Side "A" Facing
Center of Door
Maximum
Minimum
Maximum
Distance
Distance
Distance
8-9/16"
10-3/32"
11-3/32"
9-9/16"
11-3/32"
12-3/32"
11-9/16"
13-3/32"
14-3/32"
11-9/16"
13-3/32"
14-3/32"
14-9/16"
16-3/32"
17-3/32"
14-9/16"
16-3/32"
17-3/32"
14-9/16"
16-3/32"
17-3/32"
14-9/16"
16-3/32"
17-3/32"
23-9/16"
25-3/32"
26-3/32"
BACK OF DOOR
BACK OF DOOR
7-1/2"
7-1/2"
Side "A" Facing
Center of Door
3
3
Publicidad
