Publicidad
Enlaces rápidos
Publicidad
Manuales relacionados para Little Tikes T-Rex
Resumen de contenidos para Little Tikes T-Rex
- Página 1 T-Rex Truck ASSEMBLY INSTRUCTIONS #656705M #656705MX1 Adult assembly required. Approx. assembly time: 50 min. Look for video of assembly at littletikes.com/videoinstructions XIM656705-R2 - 3/21 Q.C.'d by: LW Date: 03/11/2021 Cyan Magenta Yellow Black PMS Colors are Simulated...
- Página 2 • Clear a flat surface to lay out all the materials so everything is close at hand. • You will need a Phillips head screwdriver (power driver, recommended, not included) hammer and safety glasses (not included) to assemble the T-Rex Truck. - When installing screws, be sure screws are tightened snugly, but do NOT OVERTIGHTEN.
- Página 3 BATTERY SAFETY INFORMATION: • Keep these instructions for future reference. • Replace with 2 “LR44” button cell batteries (not included). • The voltage of a fully-charged, rechargeable battery is often lower than that of a fresh alkaline battery. Therefore, it is recommended that alkaline batteries be used instead of rechargeable batteries for best performance and longer play time.
- Página 4 BEFORE you begin assembly, make sure you have all the parts listed below. Some packages of hardware may have extras pieces. Questions? We’re here to help. Little Tikes customer service team at 1-800- 321-0183. T-Rex body (1) Truck Body (1) Door (1)
- Página 5 Front Wheel Wheels (4) Center caps (4) Axles Left Right NOTE: Distance from end to the notch on the “Left” axle is less than the notch on the “Right” axle. Hubcaps (4) Small axle (1) (1) Decal sheet is located in the hardware pack.
- Página 6 Ready...let’s start with decals! Decals must be applied to a clean, dry surface. Wipe clean with a dry rag before application. Remove air from under decals by applying pressure to the decals starting from the center, and work towards edges. NOTE: If decals bubble, prick with a pin to remove the air. Decals are located in the bottom of the cardboard box.
- Página 7 Arms first!! Insert both arms (parts N1,N2) into the T-Rex body (part A). Push them together. You will feel them lock into each other. Once together they will NOT COME APART. Arm - Right (1) Arm - Left (1) You should also feel a CLICK...
- Página 8 Fit the reins (part G) onto the T-Rex body. Align the holes in the reins to the holes in the body. Thread the small axle through the reins and T-Rex head.
- Página 9 Attaching the reins - one more step Flip T-Rex body and reins over. Place the small cap nut (CC) and the small cap nut tool over the OPEN end of the axle. Hammer the small cap nut onto axle. Do not hammer on surfaces or items you don’t want to...
- Página 10 Choose your lock First, install door latch (part F) into door (part C) Attach using (1) ” (1.27 cm) screw. " (1.27 cm) DOOR LOCKS AND TO PERMANENTLY UNLOCKS LOCK THE DOOR Add (1) additional 1/2” (1.27 cm) screw Next, insert door (part C) into truck body (part B). Q.C.'d by: LW Date: 03/11/2021 Black PANTONE 485 C...
- Página 11 Dashboard holds the door in place Install dashboard (part D) into truck body (part B). Be sure to fit the dashboard securely over the door pin. Flip the truck body over before securing the screws. " (3.81 cm) Attach using (2) 1 ”...
- Página 12 Attach the Grrrrill! Leave the truck body Slide grill (part E) onto front end of upside down for the next truck body (partB). 3 steps. Secure grill using (7) 1” (2.54 cm) screws. 1" (2.54 cm) Q.C.'d by: LW Date: 03/11/2021 Black PANTONE 485 C PMS Colors are Simulated...
- Página 13 Handle it! TURN TRUCK BODY RIGHT SIDE UP. Insert handle bar (part M) into back of truck body (part B). Make sure notched side is facing toward the BACK! Q.C.'d by: LW Date: 03/11/2021 Black PANTONE 485 C PMS Colors are Simulated...
- Página 14 Ready for REAR wheels... Really give it a good hit! top hat Do not hammer on surfaces or items you don’t want to break, mar or dent. Rear axle Top hat tool Place top hat (part AA) into top hat tool. Insert the large axle (part U) into the top hat.
- Página 15 Ready for REAR wheels...cont. First slide assembled axle THROUGH the truck body. Next, slide (1) washer (DD) then(1) rear axle bushing (FF) then slide wheel (O), then hubcap (S) onto axle. rear axle washer hubcap wheel bushing Q.C.'d by: LW Date: 03/11/2021 Black PANTONE 485 C PMS Colors are Simulated...
- Página 16 REAR wheels...last step. Flip the truck on its side. Place a top hat (AA) and the top hat tool over the OPEN end of the axle. Hammer the top hat onto axle. Really give it a good hit! Do not hammer on surfaces or items you don’t want to Top hat tool...
- Página 17 And next the FRONT wheels bushing bushing First, pull grill (part E) away from axle hole. Insert (1) bushing (EE) onto each axle and push down in place. Grill bushing Next, find the Left and Right Axles. Axles are NOT IDENTICAL. Left Right NOTE:...
- Página 18 And next the FRONT wheels...cont. Slide onto LEFT front axle (L), (1) washer (DD), (1) hubcap (S) and (1) wheel (O). washer top hat Top hat tool Place top hat then top hat tool onto open end of axle. Hammer top hat onto axle. REPEAT these steps for RIGHT front axle Q.C.'d by: LW Date: 03/11/2021 Black...
- Página 19 And next the FRONT wheels...cont. First, slide (1) washer (DD), then bushing (EE) onto assembled right axle. REPEAT on left side. Then, attach FRONT wheels and axles. bushing washer Insert axle “R” (for right) Insert axle “L” (for left) into body. into body.
-
Página 20: Front Wheels
IMPORTANT! Check axle positions - roll the T-Rex Truck forward - HUBCAPS SHOULD STOP FACING OUTWARD. FRONT wheels...last steps! Really give it a good hit! Place axle cap then long axle cap tool onto open end of axle. Hammer axle Long axle cap tool cap onto axle. - Página 21 Let’s get the horn working WARNING: Remove battery cover before pulling tab. Remove battery cover on horn (part J) Pull clear tab from horn unit to activate. Re-attach batter cover. Snap horn (part J) into center of steering wheel (part I). Remove battery cover from horn.
- Página 22 Steering T-Rex is easy. Squeeze steering clip (part Ib) Steering clip should snap into MIDDLE into steering wheel (part I). hole on each side of the steering column. Insert steering wheel Make sure the steering clip through hole in dashboard snaps past the O ring.
- Página 23 Let’s put this all together! Insert assembled TRex body over the post on the grill. 1" (2.54 cm) Place the grill cap (H) over the top of grill. Secure using (5) 1" (2.54 cm) screws. Q.C.'d by: LW Date: 03/11/2021 Black PANTONE 485 C PMS Colors are Simulated...
-
Página 24: Avertissements
INSTRUCTIONS DE MONTAGE Montage par un adulte requis. Durée de montage approximative : 50 min. © Merci d’avoir choisi l’ensemble de Little Tikes Camion T-Rex. Nous sommes déterminés à fournir un jouet durable et facile à monter, procurant à votre enfant des années de plaisir créatif! Veuillez lire ces renseignements •... - Página 25 Étape 2 : Les bras d’abord! • Les bornes d’alimentation ne doivent pas être court- Insérez les deux bras (pièces N1,N2) dans le corps du T-Rex circuitées. (pièce A). Poussez-les pour les emboîter. REMARQUE : Si le module cesse de fonctionner ou ne Vous les sentirez s’emboîter les uns aux autres.
- Página 26 Étape 14 : Mettons tout cela ensemble! Étape 11 : Ensuite, les roues AVANT Insérez le corps du T-Rex assemblé sur le port de la calandre. D’abord, éloignez la calandre (pièce E) du trou d’essieu. • Placez le couvercle de la calandre (H) sur le dessus de la •...
-
Página 27: Información Realmente Importante Que Debería Conocer
El montaje debe realizarlo un adulto. Tiempo aproximado de montaje: 50 min. © Gracias por elegir el “Camión T-Rex” de Little Tikes . Nos esforzamos por crear juguetes perdurables, fáciles de ensamblar y creados para durar, que brindan a sus niños años de diversión fascinante y ocurrente. -
Página 28: Guía De Materiales
• Las terminales de alimentación no deben permanecer Paso 2 : ¡Los brazos primero! activadas. Inserte ambos brazos (piezas N1 y N2) en el cuerpo del T-Rex NOTA: Si la unidad deja de funcionar o no funciona como (pieza A) al mismo tiempo. Júntelos. - Página 29 Paso 14 : ¡Juntemos todo! En primer lugar, aleje la rejilla (pieza E) del orificio del eje. Inserte el cuerpo del T-Rex montado sobre el poste en la rejilla. • Inserte (1) el buje (EE) en cada eje y empújelo hasta que •...
- Página 30 Q.C.'d by: LW Date: 03/11/2021 Black PMS Colors are Simulated...
- Página 31 Q.C.'d by: LW Date: 03/11/2021 Black PMS Colors are Simulated...
-
Página 32: Consumer Service
LIMITED WARRANTY The Little Tikes Company makes fun, high quality toys. We warrant to the original purchaser that this product is free of defects in materials or workmanship for one year * from the date of purchase (dated sales receipt is required for proof of purchase).