Use And Maintenance - hafele 539.82.019 Manual De Utilización

1) Mounting of the cooker hood on the lower side of the
cupboard.
2) Selection of the version (extraction or filtration)
• FITTING THE COOKER HOOD INTO THE LOWER PART
OF THE WALL CABINET
For all measurements relating to the cooker hood, please
refer to Fig. 1.
Before fixing the cooker hood to the lower part of the cabinet,
the following steps should be performed:
1. Remove the 4 screws E fixing the two cooker hood
brackets H (RHS and LHS) in place as indicated in Fig. 2A.
2. Remove the brackets H as shown in Fig. 2B.
3. Make sure the thickness of the cabinet falls within the
range of values listed in Fig. 2C.
Fit the cooker hood in the cabinet (Fig. 3) and make sure
the 4 springs are fixed in place well.
Fix the cooker hood to the cabinet securely by using a
screwdriver to tighten the screws M until the appliance is
flush with the cabinet (Fig. 3).
• EXTRACTOR VERSION
When installed in this way the appliance expels fumes
outside, either through a perimeter wall or through existing
ducting.
It is therefore necessary to purchase a non-flammable air
exhaust tube (not supplied) which complies with all current
legislation and connect it to flange N (Fig. 6).
• FILTER VERSION
To transform an extractor hood version into a filter hood
version, contact your appliance dealer and ask for active
carbon filters.
The filters should be fitted to the extraction assembly inside
the hood, by centring them and rotating them 90 degrees,
until they click into place (Fig. 10). Remove panels G when
performing this procedure (Fig. 8 - 9). The air is released
back into the room through an air exhaust pipe which passes
through the cabinet and is connected to air exhaust hole N
(Fig. 7).

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on before
any food is cooked. We also recommend that the appliance
is left running for 15 minutes after the food is cooked, in
order to thoroughly eliminate all contaminated air.
The effective performance of the cooker hood depends on
constant maintenance; the anti-grease filter and the active
carbon filter both require special attention.
• The anti-grease filter is used to trap any grease particles
suspended in the air, therefore is subject to saturation (the
time it takes for the filter to become saturated depends on
the way in which the appliance is used).
The acrylic filter, which is found resting on the grille, should
be replaced when the text, visible through the grille, changes
colour and the ink spreads; the new filter should be fitted in
such a way that the text can be seen through the grille from
outside the cooker hood.
If the filters do not have any text on them, or if metal filters
or aluminium panel filters are used, they should be washed
every 2 months in order to prevent the risk of fire. To wash
the filters, proceed as follows:
- Remove the filter from the grille and wash it using a solution
of water and neutral liquid detergent, leaving the dirt to
soften.
- Rinse thoroughly with warm water and leave to dry.
The metal filters and/or aluminium panel are also
dishwasher safe. If the filters are made using aluminium, or
if an aluminium panel is used, after a few washes the colour
may change. This does not mean they have to be replaced.
If the replacement and washing instructions are not followed,
the anti-grease filters may present a fire hazard.
• The active carbon filters are used to purify the air which is
released back into the room. The filters are not washable or
re-usable and must be replaced at least once every four
months. The active carbon filter saturation level depends
on the frequency with which the appliance is used, the type
of cooking performed and the regularity with which the anti-
grease filters are cleaned.
• Remove build-up from the fan and other surfaces of the
cooker hood regularly using a cloth moistened with
denatured alcohol or non-abrasive neutral liquid detergent.
• The light on the cooker hood is designed for use during
cooking and not for general room illumination. Extended use
of the light reduces the average duration of the bulb.
COMMANDS: (Fig.12)
Push-button A = on/off lights switch
Push-button B = on/off cooker hood switch. The appli-
ance switches on at speed level 1, If the cooker hood is on
depress the push-button for 2 sec. to switch off the cooker
hood. If the cooker hood is at speed level 1 it will not be
necessary to depress the push-button to switch the cooker
hood off. Decreases the motor speed.
Display C = indicates the motor speed level selected and
activates the timer.
Push-button D = switches on the cooker hood. Increases
the motor speed. Touching the key at 3rd speed, the inten-
sive function runs for 10', then the appliance go back to
work at the original speed. During this function the display
blinks.
Key E = The Timer times the functions on activation for 15
minutes, after which they are switched off. The Timer is
deactivated by re-pressing Key E. When the Timer is acti-
vated the decimal point must flash on the display. The Timer
cannot be activated if the intensive speed is functioning.
The "clean air" function is activated by pressing key E for 2
seconds when the appliance is switched off. This switches
the motor on for 10 minutes every hour at the first speed.
During functioning a rotary movement of the peripheral seg-
ments must be visualised on the display. When this time
has passed the motor switches off and the fixed letter "C"
must be visualised on the display until the motor re-starts
after 50 minutes for another 10 minutes and so on. Press
any key apart from the light keys to return to normal
functioning. Press key E to deactivate the function.
• Active carbon/grease filter saturation:
- When display item C flashes, at a speed where it alternates
with the letter F (e.g. 1 and F), the grease filters must be
washed.
- When display item C flashes, at a speed where it alternates
with the letter A (e.g. 1 and A), the carbon filters must be
replaced.
After the clean filter has been positioned correctly, the
electronic memory must be reset by pressing button A for
approximately 5 seconds, until the indication F or A shown
on the display C stops flashing.
• COMMANDS:
(Fig.13) LUMINOUS the key symbols are explained below:
A = LIGHT
B = OFF
C = SPEED I
D = SPEED II
E = SPEED III
F = AUTOMATIC STOP TIMER - 15 minutes (*)
- 17 -