NAIM NAC-N 272 Guia De Inicio Rapido página 4

NAC-N 272 • English
1.
1.1 Stand your NAC-N 272 on an appropriate, stable surface. Make sure it is well ventilated.
1.2 Check that the mains voltage specified on the NAC-N 272 rear panel is appropriate for your country. Insert the supplied power
supply upgrade link plug in the rear panel Burndy socket and connect the NAC-N 272 to the mains supply using the supplied
mains cable. Do not switch on the NAC-N 272 until all other connections have been made.
1.3 Identify the rear panel Signal Ground Switch and select the chassis option unless your NAC-N 272 is connected in a hi-fi
system incorporating another earthed source component (all Naim CD players, for example), or mains hum is audible through
the speakers when it is switched on.
1.4 If the optional DAB/FM Radio Module is fitted, a suitable aerial should be connected to the DAB/FM aerial socket.
1.5 Connect a power amplifier, active crossover or multiple power amplifiers to one or both of the NAC-N 272 preamp output
sockets. NAC-N 272 preamp output sockets are also suitable for the connection of a subwoofer. Your Naim retailer will be able
to supply appropriate cables if required.
1.6 To play audio from internet radio stations, UPnP™ servers, Spotify
must be connected to the internet via a network router. Either connect the NAC-N 272 network socket to your network router
using an Ethernet cable, or connect the supplied Wi-Fi antenna to the rear panel Wi-Fi aerial socket.
1.7 For NAC-N 272 to play audio from Bluetooth
panel Bluetooth aerial socket.
1.8 If your NAC-N 272 is to play audio files stored on a USB storage device, such as an iOS device or a memory stick, connect it,
using an appropriate cable if necessary, to the front panel USB socket.
1.9 If any external audio sources are to be used with your NAC-N 272, connect them using the appropriate cables to one or more
of the rear panel analogue or digital inputs.
2. Switching On and Getting Started
2.1 Once all connections have been made, switch on your NAC-N 272 using either its rear panel on/off switch or the external
power supply on/off. The NAC-N 272 will display a welcome screen and select its Analogue 1 input or, if it has been previously
used, the last input selected.
2.2 For initial setup purposes your NAC-N 272 is best controlled from its remote handset. Use the navigation (56) keys to select
inputs or menu items and the ok/list key to confirm selections. To return to a previous menu use the left (3) key.
2.3 The NAC-N 272 interface language can be changed. Enter Setup Mode and select Language.
Installing and Connecting
®
Connect, or other Naim streamer units the NAC-N 272
®
streaming devices, the supplied Bluetooth antenna must be attached to the rear
Note: Full NAC-N 272 installation and operational information can be
found in the Reference Manual available at: www.naimaudio.com
Note 1.2: If your NAC-N 272 is to be powered by an external power supply,
remove the power supply upgrade link plug and connect the external
power supply using the appropriate Burndy cable. Do not connect the
NAC-N 272 mains cable.
Important: XPS power supplies with serial numbers below 188015 are not
compatible with the NAC-N 272 and should not be used. Contact your
local retailer or distributor for more information.
Note 1.5: The NAC-N 272 RCA phono preamp output sockets are disabled
by default. They can be enabled in the Analogue Outputs setup menu.
Enter Setup Mode by pressing the handset
Setup 1/10
setup ( ) key. Navigate setup menus by
Language
using the navigation (563) keys. Select
Inputs
options by pressing the ok/list key. Leave
4 Analogue Outputs
Setup Mode by pressing the setup or exit
Headphones
key.
Note 1.7 & 1.8: NAC-N 272 is supplied with both Wi-Fi and Bluetooth
aerials. Each aerial must be fitted to the correct rear panel aerial socket.
The Bluetooth aerial is the shorter one of the two.
Note 1.9: Most UMS (Universal Mass Storage) USB devices are compatible
with the NAC-N 272 USB audio input. Such devices might include portable
digital music players, smart-phones, tablet computers, USB memory sticks
and memory card readers.
Note 2.1: If your NAC-N 272 is left unused it will switch to displaying the
time after two minutes. This delay time can be adjusted via the setup
menus. If the clock is not set it will display "No Time".