Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
PumP-N-Vac attachmeNt
aP31023
WarNiNg:
To reduce the risk of injury, user must read and under-
stand the operator's manual for their pressure washer
before using this accessory. To reduce the risk of injury
or property damage, spray the pressure stream in a safe
direction to ensure proper connection of all accessories
before starting any cleaning project. Fits most pressure
washers. Ensure compatibility and proper fit before using
this accessory. Wear eye protection marked to comply
with Z87.1. Risk of fluid injections; do not point at people,
pets, electrical devices or the unit itself. Turn off the pres-
sure washer before changing or adjusting accessories.
For cold water use only. Save these instructions. Refer
to them frequently and use them to instruct other users.
If you loan someone this tool, loan them these instruc-
tions also.
NOte: If you have an electric pressure washer, you may
need the Electric Spray Wand Adaptor (AP31021) to use this
Pump-N-Vac Attachment. Before installing, remove the spray
wand storage clip (see Fig. 1) using a Torx screwdriver.
assembliNg the attachmeNt
See Figure 1.
The Pump-N-Vac attachment can be used to remove stand-
ing water by either vacuuming or pumping mode.
For vacuuming mode:
n Attach the vacuum nozzle squeegee, if not installed.
n Using a flat blade screwdriver, wedge the securing pin
up until you can grasp it. Remove the securing pin.
n Attach the Y-adaptor.
n Reinstall the securing pin and push until fully seated.
For high-volume pumping mode:
n Remove the vacuum nozzle squeegee, if installed.
n Using a flat blade screwdriver, wedge the securing pin
up until you can grasp it. Remove the securing pin.
n Attach the high-volume hose adaptor.
n Reinstall the securing pin and push until fully seated.
usiNg the PumP-N-Vac attachmeNt
See Figures 2 - 3.
n Assemble the Pump-N-Vac as instructed above.
n Insert the Pump-N-Vac inlet plug into the spray wand
quick connect coupler and secure.
securing pin
hook-and-loop
strap
vacuum nozzle
squeegee
inlet
plug
pump-n-vac
in vacuum
mode
For vacuuming mode:
n Attach a garden hose (or two hoses, if desired) to the
Y-adaptor and trail away from the work area. This is where
the water that is vacuumed up will drain.
n Start your pressure washer as described in your pressure
washer manual.
n Move the Pump-N-Vac in the area where the standing water
is located until desired amount of water is removed.
y-adaptor
high volume
hose adaptor
Fig. 1
quick connect
coupler
Fig. 2
Publicidad
Resumen de contenidos para PowerCare Pump-N-Vac
- Página 1 Start your pressure washer as described in your pressure n Reinstall the securing pin and push until fully seated. washer manual. n Move the Pump-N-Vac in the area where the standing water usiNg the PumP-N-Vac attachmeNt is located until desired amount of water is removed.
-
Página 2: Cleaning The Nozzle
Using a garden hose, flush debris out of nozzle by back flushing (running the water through the nozzle backwards or from the outside to the inside). NOte: Also check the tube of the Pump-N-Vac to be sure no debris is clogged there before reassembling. securing pin n Reinstall the nozzle into the Pump-N-Vac. - Página 3 Fixer l’adaptateur en « Y ». dessus. n Réinstaller la goupille de fixation et l’enfoncer jusqu’à ce n Insérer le connecteur Pump-N-Vac dans le coupleur rapide qu’elle soit appuyée complètement. de la lance d’arrosage et serrer solidement le tout.
-
Página 4: Nettoyage De La Buse
Submerger l’accessoire Pump-N-Vac dans l’eau stagnante pour l’évacuer. NettOYage De la buse buse Voir la figure 4. Si le jet de l’accessoire Pump-N-Vac devient plus lent, la trombone buse peut être obstruée. droit n Éteindre la laveuse à pression et couper l’alimentation tube en eau. -
Página 5: Montaje Del Accesorio
Vea la figura 1. de aspirado El accesorio Pump-N-Vac se puede emplear para extraer aguas quietas mediante el sistema de aspirado o bombeo. Para usar el modo de aspirado: Fig. 2 n Conecte el escurridor de la boquilla de aspirado si no está... -
Página 6: Limpieza De La Boquilla
Encienda la lavadora de presión como se describe en el accesorio pump-n-vac manual de esa lavadora. en modo de bombeo n Coloque el accesorio Pump-N-Vac en el área donde se abrazadera para encuentran las aguas quietas hasta extraer el nivel de mangueras agua deseado.