Ryobi EMS216L-LSG Traducción De Las Instrucciones Originales página 4

Repairs should only be carried out by qualified persons
using original spare parts otherwise this may result in
considerable danger to the user.
MITRE SAW SAFETY WARNINGS
Always clamp the work piece safely and securely.
Ensure that the machine is always stable and secure
additional warnings in this manual.
cause hearing loss.
Always wear safety goggles when using the machine.
It is recommended to wear gloves for handling blades
and rough material, plus sturdy non slip shoes to
protect the feet from work pieces which may fall from
the cutting area.
Always disconnect the plug from the socket before
carrying out any maintenance or cleaning the tool.
Only plug the power lead into the socket when the tool
is switched off.
Keep the mains lead clear from the working range of the
machine. Keep it out of the area the operator stands in.
Never reach into the area near the blade unless the
blade has completely stopped.
Before use, thoroughly check the tool, cable, and plug
for any damage or material fatigue. Repairs to the
whole machine, including the power cable should only
be carried out by authorised service agents.
Always use the guards on the machine. Do not use
the machine if the guards are not in place and working
correctly.
The lower blade guard should only open when the
blade is lowered to the work piece.
Never alter of modify the saw or its function. Your safety
may be compromised.
When using the mitre saw outdoors, the manufacturer
recommends the use of an RCD device with a trip set
at 30mA.
Do not use saw blades which are cracked, damaged
or deformed.
Do not use saw blades made of high-speed steel.
Only use blades that are sharp. Replace dull blades.
Always use blades with correct size and shape of
arbour holes. Blades that do not match the mounting
hardware of the saw will run eccentrically, causing loss
of control.
Use only woodworking blades specified in this manual,
which comply with EN 847-1.
Do not use any flanges, washers and nuts to secure the
saw blade other than those supplied or indicated in the
instruction manual.
It is necessary to select a saw blade which is suitable
for the material being cut.
2
on the saw blade.
Never use the mitre saw to cut materials other than
those specified in the intended use section in this
manual.
Replace the table insert when worn or damaged.
Before work, make a dummy cut without the motor
turned on so the position of the blade, operation of the
guards with respect to other machine parts, and work
piece may be checked.
When performing mitre, bevel or compound mitre cuts,
adjust the sliding fence to ensure the correct clearance
from the blade.
The handle lock must always be engaged when
transporting the mitre saw.
Keep the floor area free of loose materials, such as
chips and cut-offs.
Refrain from removing any cut-offs or other parts of the
work piece from the cutting area whilst the machine is
running and the saw head is not in the rest position.
Long work pieces must be adequately supported. The
work piece. The operator should secure this area from
accidental contact from other persons or objects which
may move the work piece during operation.
The dust produced when using this tool may be harmful
to health. Use a dust suction system and wear a
suitable dust protection mask. Remove deposited dust
thoroughly with a vacuum cleaner.
The unit should be connected to a power circuit
protection device (fuse or circuit breaker).
Do not replace the laser or LED with a different type. Any
repairs must only be carried out by the manufacturer or
authorised service agent.
When using this tool, voltage fluctuations may affect
other electrical products or lighting on the same
power circuit. Connect the tool to a power source with
fluctuations. Contact your electric power supplier for
further clarification.
ADDITIONAL SAFETY WARNINGS FOR THE STAND
(LSG ONLY)
The stand is designed only for the Ryobi EMS216L
Sliding Compact Mitre Saw. Do not attach any other
power tool to the stand. Do not use the stand in any
way other than what is stated in the instructions.
Set up the stand on a firm level surface. A smooth
surface (tiles or wood) may cause the feet to skid
during operation. Wherever possible site the stand on
concrete or similar non slip surface.
Follow the instructions for mounting the tool carefully,
see graphics later in this manual. An improperly
mounted tool will increase the risk of serious personal
injury.
Make sure that all bolts and connecting elements of the
English