External Speaker - Sunn T50C Instrucciones De Funcionamiento

power
FUSE
on
C
B
off
A
D
• • *NOTE: Rear Panel instructions and illustrations
• •
are divided over pages (5 - 7).
A. POWER - Push UP to switch the T50C ON. Push
DOWN to switch the T50C OFF.
B.FUSE - Protects the T50C from electrical faults.
Replace FUSES only with same type and rating
(Refer to SPECIFICATIONS, F1, page 7). If the
T50C repeatedly blows FUSES, take the T50C to
an authorized Fender Service Center.
C.IEC LINE CORD CONNECTOR - Connect the
LINE CORD to a grounded AC receptacle in
accordance with the voltage and frequency rat-
ings shown on the Rear Panel of the T50C (See
illustration above, INPUT POWER {D}).
E. HIGH/LOW OUTPUT POWER - Switch UP for 50-
Watts. Switch DOWN for 12.5-Watts (The LOW
OUTPUT setting was designed to provide the
same tone characteristics of the HIGH OUTPUT
setting, at lower volume levels).
F. MAIN AMPLIFIER OUT - When using the T50C as
the "master" amp in a "chain," use this jack as
output to a "clone" amp, (See MULTIPLE T50C
CONNECTIONS, page 7).
G.EXTERNAL AMPLIFIER IN - When using a T50C
as a "clone" amp in a "chain," use this jack as
input from the "master" amp.
H.FOOTSWITCH (INCLUDED) - Plug in the
FOOTSWITCH at
FOOTSWITCH to:
• • Switch ON/OFF the effects LOOP*
• •
• • Switch ON/OFF the REVERB effect
• •
• • Select either channel-1 or channel-2*
• •
*NOTE: These switching functions are disabled
from the T50C's cabinet switches when the
FOOTSWITCH is plugged in.
I. EXTERNAL SPEAKER - Plug in a maximum of
three Sunn 112 Extension Cabinets connected
together at this jack.
SUNN MODEL T50C – REAR PANEL*
output power
high
low
E
this jack. Use
main ext.
amp out amp in footswitch
F G H
J. MAIN SPEAKER - Connect the T50C's INTERNAL
SPEAKER (or other speaker, 4Ω minimum) at this
jack. NOTE: The MAIN SPEAKER jack must
ALWAYS have a speaker connected to it when the
T50C is ON, or damage may occur to the T50C.
ALWAYS switch the T50C OFF before connecting
speakers.
K.LOAD IMPEDANCE - Select an IMPEDANCE,
(4Ω/8Ω/16Ω) that matches the total SPEAKER-
LOAD IMPEDANCE (both speaker jacks {I+J}
together): Standard parallel speaker connections
with their proper LOAD IMPEDANCE settings are
shown below:
{J} MAIN SPKR +
JACK
T50C Internal
(Speaker 16Ω)
T50C Internal
(Speaker 16Ω)
T50C Internal
(Speaker 16Ω)
T50C Internal
(Speaker 16Ω)
T50C Internal
the
(Speaker 16Ω)
T50C Internal
(Speaker 16Ω)
Any External
(Speaker 8Ω)
Any External
(Speaker 8Ω)
Any External
(Speaker 4Ω)
5
MAX. PWR. OUT 70W RMS
MIN. LOAD 4Ω TOTAL
ext. main
spkr. spkr.
16Ω 8Ω 4Ω
load impedance
I J
{I} EXT SPKR = {K} LOAD
JACK IMPEDANCE
SETTING
+ NONE =
1 Sunn 112
+ (16Ω) =
2 Sunn 112's
+ (8Ω) =
3 Sunn 112's
+ (5.3Ω) =
Sunn 412
+ (16Ω) =
Any External
+ (8Ω) =
+ NONE =
Any External
+ (8Ω) =
+ NONE =
K
16Ω
8Ω
4Ω
4Ω
8Ω
4Ω
8Ω
4Ω
4Ω