Inserting/Replacing The Battery - Flex DD 2G 10.8-LD Instrucciones De Funcionamiento Originales

Inserting/replacing the battery

 Press the charged battery into the power tool until it
clicks into place (Figure C).
 To remove, press the release button (1.) and pull out the
battery (2.) (Figure D).
CAUTION!
Protect the battery contacts when the battery is not being
used. Loose metal parts may shortcircuit the contacts –
Explosion and fire hazard!
Battery state of charge (Figure E)
 Press the button to check the state of charge at the state
of charge indicator LEDs.
The indicator goes out after 5 seconds.
If one of the LEDs flashes, the battery must be recharged. If
none of the LEDs light up after the button is pressed, the battery
is faulty and must be replaced.
Direction preselection (Figure F)
CAUTION!
Change the direction of rotation only when the power tool is
stopped.
 Move the direction preselector switch to the required
position:
– Left: counterclockwise (remove screws, release screws)
– Right: clockwise (drill, insert screws, tighten down screws)
– Middle: switchon interlock (tool change, when working on
the power tool)
Torque preselection (Figure G)
CAUTION!
Change the torque only when the power tool is stopped.
 Move the torque setting turning dial to the required position.
1–17: Screwing
Drilling
NOTE
The safety clutch is deactivated in the Drilling setting
Speed preselection (Figure H)
CAUTION!
Change the speed only when the power tool is stopped.
 Move the selector switch to the required stage:
1: Low speed, high torque
2: High speed, low torque
Inserting the tools (Figure I)
CAUTION!
Before carrying out any work on the power tool, move the
direction preselector switch (2) to the middle position.
Drill bits with a diameter of 1.5–10 mm, ¼" screwdriver bits and
¼" bit holders are securely held in the chuck.
 Grip the power tool firmly with one hand and turn the chuck
with the other hand.
– Turn counterclockwise to open the chuck further.
– Turn clockwise to close the chuck.
 Insert the tool.
 Close the chuck fully.
14
 Move the direction preselector switch to the required
position (left/right).
 Carry out a test run to check that the tool is chucked in
the centre.
Switching on the power tool (Figure J)
To switch the power tool on:
 Press the trigger switch.
The power tool trigger switch allows the operator to
increase the speed in increments up to the maximum
speed.
To switch the power tool off:
 Release the trigger switch.
NOTE
– The power tool is equipped with a brake which stops the
cutting accessory as soon as the trigger switch is
released.
– When using the power tool continuously, the operator
should work primarily with the trigger switch fully
depressed.
Working with the power tool (Figure K)
CAUTION!
Before carrying out any work on the power tool, move the
direction preselector switch (2) to the middle position.
1. Insert the battery.
2. Insert the tool (drill bits, srewdriver bits, bit holders).
3. Set torque preselection to the required setting.
4. Set speed to the required setting.
5. Set the required direction of rotation.
6. Hold the power tool with one hand on the handle and
assume the working position.
7. Switch on the power tool.
At the end of work:
8. Release the trigger switch.
9. Move the direction preselector switch (2) to the middle
position.
Charger (Figure L)
.
The CA 10.8 charger is designed to charge FLEX batteries
of the following types
– AP 10.8/2.5,
– AP 10.8/4.0 and
– AP 10.8/6.0.
1 Insertion slot for battery
2 Contacts
3 LED fault message (red)
4 LED charge status (green)
5 Ventilation slots
6 Power cord with mains plug
DD 2G 10.8-LD