Publicidad
Idiomas disponibles
Idiomas disponibles
INSTRUCTIONS FOR USE:
1 - Loosen the clamp clip (3) and set it horizontally, x the clamp softly.
2 - Once we have the horizontal, open and xed clamp we can proceed to lift the bike
manually, when we hold the bike on the clamp we proceed to tighten (2) said clamp according
to the type of frame.
3 - Once the bike is already fastened with the clamp (1), loosen the side stick (3), look for the
necessary angle according to the inclination of the frame or the work to be performed, x the
stick of the clamp (3) to keep at the desired angle.
4 - The clamp has no tightening stop, the user must determine the pressure (2) he needs
according to the work to be performed and the type of frame to be fastened.
It is important to know the type of frame to be fastened, as the carbon frames are weaker at
tightening.
*For this type of frame there is a special clamp (Goliath 360° Carbon) that allows covering
more frame surface and reducing the e ort per square centimeter, it also has a softer
polyurethane protection and designed to prevent the frame from rolling even with less
pressure. (See our product catalog)
5 - With the bike raised we can rotate it on the axis of the desired clamp.
For this operation we only have to loosen the side loop (3) that secures the clamp.
Once the bike is in the desired position, proceed again to tighten the side loop so that it
remains xed in that position.
6 - Whenever we intend to rotate 180° (or other angle) we must make sure that the clamp has
the necessary pressure (2) on the frame so that it does not roll and can tip sideways.
To return to the starting position, simply loosen the side clip (3) again and hold the bike to its
plane position or the angle you want.
It is very important to make this operation of ipping the bike 180° as simple and
of little e ort so that when you hold the bike you look for the most approximate
center of gravity.
7 - Once you have nished lifting work and want to lower the bike to its starting position, you
should look for the horizontal plane of the clamp before opening it, once opened you can
lower the bike manually.
8 - Goliath Wall can hold certain Goliath accessories. (See catalog)
HAZARD WARNINGS IN THE USE OF GOLIATH G-WALL:
1 - Always place the bike in the elevator as centered as possible, always searching for the approximate center of gravity.
2 - Do not hold the bicycle at the ends under any circumstances.
3 - Always hold the clamp in rigid areas of the frame, avoid plastic beautifying housings or other weak areas.
4 - The bracket must not be operated by children, only by adults.
5 - It should be veri ed that the wall is in good condition and that it will support the anchoring and weight of the bracket
once bolted.
IT IS FORBIDDEN TO WORK UNDER THE LIFTED LOAD WITHOUT SECURING IT WITH APPROPRIATE ADDITIONAL MEANS.
WARNINGS IN CASE OF REPAIR OF THE GOLIATH G-WALL STAND:
1- Only use spare parts from the manufacturer or authorized supplier.
2- The manufacturer cannot be held responsible for any modi cations made without prior authorization from the
manufacturer.
3- Only use the GOLIATH G-WALL stand according to the manufacturer's instruction manual.
4- Only carry out maintenance and repairs in accordance with the manufacturer's instruction manual.
5- Repairs and maintenance may only be performed by quali ed personnel.
MAINTENANCE:
1 - The bracket does not require any speci c maintenance.
2 - The only grease point can be the clamp holder and tightening loop, which must be lubricated with a little grease,
petroleum jelly etc.
This greasing process should be done to the user's liking and although it is not necessary, if it contributes to the smoother
movements.
WARNING
THE CLOSING PRESSURE OF THE 360º BASIC CLAMP MUST BE DETERMINED
BY THE USER FOR ITS CORRECT OPERATION.
GOLIATH BIKE WILL NOT BE HELD RESPONSIBLE FOR ANY DAMAGE CAUSED
TO THE FRAME OR ANY PART OF THE BICYCLE DUE TO MISUSE OF THE 360º
BASIC CLAMP, THE USER BEING SOLELY RESPONSIBLE.
IN NO CASE SHOULD THE 360º BASIC CLAMP (G-AC014) BE USED TO HOLD
CARBON FRAMES. FOR THIS WE HAVE THE 360º CARBON CLAMP DESIGNED
EXCLUSIVELY TO EXERT LESS PRESSURE AND NOT DAMAGE CARBON FRAMES.
GOLIATH BIKE manufactured by:
METSISTEM ELDA S.L.
Los Cisnes 12, Elda (Alicante), España
NIF: B54557798
info@goliath-bike.com
WWW.GOLIATH-BIKE.COM
Publicidad
