Publicidad
IS216 / IS216T Passive Infrared Motion Sensor - Installation Instructions
SPECIFICATIONS
Power: 8.5 – 15.4 VDC
(UL: 10 – 14 VDC), nominal 12
VDC, 18mA max; AC Ripple: 50
to 120 Hz; 3 V peak-to-peak at
nominal 12 VDC
Alarm Relay: Form A (Normally
Closed); 30 mA, 24 VDC max.; 40
Ohms resistance max.
Tamper Switch (IS216T):
Closed with cover in place; 30
mA, 24 VDC
Operating Temperature:
– 10° to 55° C (14° to 131° F)
(Indoor use environment)
Relative Humidity: 5% - 95%,
non-condensing
Temperature Compensation:
Advanced Dual Slope
Dimensions: 8.57 cm x 6.03 cm x
3.81 cm (3-3/8 in x 2-3/8 in x
1-1/2 in)
Weight: 66.62 g (2.35 oz);
Packaged: 92.14 g (3.25 oz)
APPROVAL LISTINGS / AGREMENT / HOMOLOGACIÓN /
HOMOLOGAÇÃO
FCC part 15, Class B verified
IC, ICES-003, Class B verified
CE
cULus Listed
UL COMPLIANCE NOTES
Product must be tested once each year.
-
NOTES DE CONFORMITÉ
Le produit doit être testé au moins une fois par an
-
NOTAS DE CUMPLIMIENTO UL
Se debe probar el producto una vez al año.
-
NOTAS DE CUMPRIMENTO DA NORMATIVA UL
O produto deve ser provado uma vez por ano.
-
FCC NOTICE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
− Reorient or relocate the receiving antenna.
− Increase the separation between the equipment and receiver.
− Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
− Consult the dealer or an experienced radio/television technician for help.
The user is cautioned that changes or modifications not expressly approved
by Honeywell could void the user's authority to operate this equipment.
To obtain applicable EU compliance Declaration of Conformity for this product, please refer to our Website:
Les déclarations de conformité aux normes Européennes de ce produit sont disponibles sur notre site Internet à l'adresse :
Para obtener la Declaración de conformidades de cumplimiento aplicable para este producto, consulte en nuestro sitio Web :
Para obter a Declaração de Conformidades de adequação aplicável para este produto, consulte nosso site:
http://www.security.honeywell.com/hsce/international/index.html.
PRELIMINARY DRAFT 9/15/09
All manuals and user guides at all-guides.com
CARACTERISTIQUES
Alimentation: 8,5 à 15,4 Vcc
(UL: 10 – 14 Vcc) ; 16 mA nominal à
12 Vcc, 18 mA max.; 3 Vc-à-c à
12 Vcc
Relais d'alarme: Normalement
fermé 30 mA, 24 Vcc max., 40 Ohms
de résistance max.
Autoprotection (IS216T) : Fermée
avec le capot en place 30 mA, 24 Vcc
Température de fonctionnement:
– 10° C à +55° C
Humidité relative: 5% à 95% sans
condensation
Compensation en température: A
double pente
Dimensions: 8.57 cm x 6.03 cm x
3.81 cm
Masse: 66.62 g;
Emballé: 92.14 g
ESPECIFICACIONES
Energía: 8.5 – 15.4 VDC
(UL: 10 – 14 VDC), nominal 12 VCD,
18mA max; Oscilación de CA: 50 a
120 Hz, 3V pico a pico a 12 VCD
nominales
Relé de alarma: De A (normalmente
cerrado); 30 mA, 24 Vcc max, 40
Ohms resistencia máxima
Salida de tamper (IS216T):
Cerrado con la tapa en su sitio; 30
mA, 24 Vcc
Temperatura de funcionamiento:
– 10° C to +55° C (para uso en
interiores)
Humedad relativa: 5% to 95% sin
condensación
Compensación de temperatura:
Doble pendiente avanzada
Dimensiones: 8.57 cm x 6.03 cm x
3.81 cm
Peso: 66.62 g;
Embalaje del producto: 92.14 g
ACCESSORIES / ACCESSOIRES / ACCESORIOS /
ACCESSÓRIOS
SMB-10
(P/N 0-000-110-01)
SMB-10C
(P/N 0-000-111-01)
SMB-10T
(P/N 0-000-155-01)
IC NOTICE: This Class B digital device complies with the Canadian ICES-
003.
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du
Canada.
This Class B digital device complies with RSS-210 of the IC rules. Operation
is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Cet appareil numérique de la Classe B est conforme à la norme CNR-210 des
règles d'IC. L'utilisation de ce dispositif est autorisée seulement aux deux
conditions suivantes ; (1) il ne doit pas produire de brouillage, et (2)
l'utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique
reçu, même si ce brouillage est susceptible de compromettre le
fonctionnement du dispositif.
- 3 -
ESPECIFICAÇÕES
Energia: 8.5 – 15.4 VDC
(UL: 10 – 14 VDC), nominais a
12 VDC, 18mA máx; Oscilación
AC: 50 Hz a 120 Hz; 3V pico-a-
pico a 12 VDC nominais
Relé de alarme: Forma A
(normalmente fechado); 30 mA,
24 VDC máx.; 40 Ohms
resistência máxima.
Tamper (IS216T):
Normalmente fechado (com
tampa colocada); 30 mA, 24 VDC
Temperatura de Operação:
– 10° to 55° C (aplicação
interior)
Umidade relativa: 95%; sem
condensação
Compensação de
Temperatura: Dupla
Compensacao
Dimensões: 8.57 cm x 6.03 cm x
3.81 cm
Peso: 66.62 g;
Com a embalagem: 92.14 g
Swivel Mount Bracket
Rotule de montage
Soporte giratorio de instalación en techo
Suporte Giratório de Montagem no Teto
Swivel Mount Ceiling Bracket
Rotule de plafond
Soporte de instalación en techo giratorio
Suporte de Montagem no Teto Giratório
Swivel Mount Bracket w/Tamper
Rotule de montage avec autoprotection
Soporte giratorio de instalación con tamper
Suporte Articulado com Tamper
Publicidad
