Problem Solver - Monogram ZDT985SPNSS Manual Del Propietário

Questions? PROBLEM
Use this
Start status
indicator
problem
light
solver
flashing
Dishwasher
BEEPS
once every
minute
Display
shows
"LEAK
DETECTED"
Beeping at
the end of
the cycle
(on some
models)
Dishes and
flatware not
clean
Spots and
filming on
glasses and
flatware
49-4000215 Rev. 2
POSSIBLE CAUSE
The door was opened or
the cycle was interrupted.
This is a reminder that
your dishwasher door
has been left open during
operation. It will continue
beeping until you press
START and close the door.
Possible leak is detected
This is normal. The
dishwasher will beep
twice
at the end of the cycle.
Ultra Fine or Fine filter is
clogged
Low inlet water
temperature
Water pressure is
temporarily low
Air gap or disposer is clogged
Improper rack loading
Poor performing
detergent
Leak detected
Extremely hard water
Low inlet water temperature
Overloading or improper
loading of the dishwasher
Old or damp powder
detergent
Rinse agent dispenser empty
Too little or low
performing detergent

Problem Solver

Dishwasher
WHAT TO DO
• Press the START pad once and close the door within
4 seconds to start the dishwasher.
• Press the START pad a second time when the
dishwasher is running only if you wish to cancel the cycle.
• Press START and close the door.
• Some models are equipped with leak detection and
the cycle will be cancelled if a leak is detected. The
display will show "LEAK DETECTED". Contact us for
service.
• To turn off the double beep indicator (or re-activate it if
it was previously turned off), press the DRY OPTIONS
pad 5 times within 3 seconds. A triple beep will sound
to indicate the end-of-cycle beep option has been
turned on or off.
• See the Care and cleaning section.
• Make sure inlet water temperature is correct (see the
Using the dishwasher section). Turn on the hot water
faucet nearest the dishwasher, let run until the water
temperature stops rising. Then start the dishwasher
and turn off the faucet. This ensures the entering
water is hot. Select Boost Temp.
• Turn on a faucet. Is water coming out more slowly than usual?
If so, wait until pressure is normal before using your dishwasher.
Normal water pressure to the dishwasher should be 20-120 psi.
• Clean the air gap or flush the disposer.
• Make sure large dishware does not block the
detergent dispenser or the wash arms. See the
Loading the dishwasher section.
• Use high quality detergents such as
Platinum™ ActionPacs™ or
Automatic Dishwashing
• Some models are equipped with leak detection and the cycle
will be cancelled if a leak is detected. The display will
show "LEAK DETECTED". Contact us for service.
• Use high quality rinse agents such as Cascade
Platinum™ Power Dry™ Rinse Aid or
Rinse Aid to prevent spots and prevent new film build-up.
• If water is extremely hard, a softener may be required.
• Make sure water temperature is at least 120°F (49°C).
• Load dishwasher as shown in the Loading Place
Settings section.
• Make sure detergent is fresh.
such as Cascade Platinum™ ActionPacs™ or
®
Quantum Automatic Dishwashing
®
• Refill with high quality rinse agents such as Cascade
Platinum™ Power Dry™ Rinse Aid or
Rinse Aid.
• Make sure you use the proper amount of highly rated
detergent.
Cascade
®
Finish Quantum
® ®
Detergent.
®
Finish Jet-Dry
®
Use high quality detergents
Finish
Detergent.
®
Finish Jet-Dry
®
®
®
®
23