Fender Rumble 150 Instrucciones De Funcionamiento página 6

Thanks for buying a Fender® Rumble™ series bass amplifier. Fender
bass amplification provides thick, natural and balanced tone that
sits fat in your live or studio mix. Rumble amps are designed by
bass players. Full-featured and easy to operate, the Rumble family
gives you high-quality bass tone and incredible value.
O V E R D R I V E S H A P E
5 5 50%
2 8 2 8
0 10 0 10 CLEAN DRIVE
- 6 dB ENABLE PUNCH SCOOP
INPUT V OLUME GAIN BLEND
A. INPUT — Plug your passive or active bass in here. If your
bass is too hot and causes distortion, try using the -6dB
switch.
B. -6 dB — Press this switch IN to provide additional
headroom for hotter basses.
C. VOLUME — Controls the loudness of the amplifier.
D. GAIN — Controls the amount of OVERDRIVE distortion.
F. BLEND — Controls the amount of distorted signal (set
by GAIN) to be blended with the clean bass signal.
Lower settings can maintain a cleaner tone, with some
added grit. Higher settings will produce more distorted
tones and add sustain.
E. ENABLE — Press this button to turn the OVERDRIVE
on or off. The red LED (light) illuminates when the
OVERDRIVE is on.
G. SHAPE FILTERS:
• PUNCH — Emphasizes tight punchy bass response,
useful for finger style playing or for enhancing the tonal
character of a bridge pickup.
• SCOOP — Mid-frequency cut, combined with low-and-
high-frequency boosts that offer a fat pleasing tone,
useful for slap style playing, low-volume practice, or in
combination with OVERDRIVE.
H. 4-BAND EQUALIZATION (RUMBLE 150 ONLY)— Used
to adjust overall tone and to compensate for room
acoustics. Remember, what sounds harsh in one room
may have just the right edge in another room.
6 6
Rumble™ 150 / 350 Bass Amps Rumble™ 150 / 350 Bass Amps
E Q U A L I Z A T I O N
0 0 0 0
-15 -15 -15 -15
+15 +15 +15 +15
150W BASS
BASS LOW MID HIGH MID TREBLE A M P L I F I E R
fender.com fender.com
The Fender Precision Bass® Guitar was introduced in 1951, forever
changing music and giving birth to a new kind of musician—the
electric bassist. Since then music has never been the same. Your
new Rumble will provide years of enjoyment as you continue your
musical journey and make history!
CAUTION:
CHASSIS SURFACE HOT
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE
AVIS:
R I S Q U E D E C H O C E L E C T R I Q U E N E P A S O U V R I R
AT TENTION:
S U P E R F I C I E D E C H A S S I S C H A U D E
TYPE: PR 851
SERIAL NUMBER
INPUT POWER
120V 60Hz
C US
POWER
158744
400W
I. 3-BAND EQUALIZATION WITH SEMI-PARAMETRIC
MIDRANGE (RUMBLE 350 ONLY) — Having more
control over the midrange frequencies is very important
in defining your bass tone. The Rumble 350 is equipped
with a semi-parametric midrange with FREQUENCY
and LEVEL controls that work together to allow greater
flexibility to adjust a specific range of frequencies (tones).
Use the FREQUENCY knob to select which frequencies
you would like to adjust, and use LEVEL to control how
much to boost or cut at these frequencies. Boosting
upper-mids (FREQUENCY near 1.5kHz) and favoring the
bridge pickup on your instrument creates a biting tone
that is great for Jazz Fusion type melodic lines. Cutting
mids (FREQUENCY near 700Hz) is useful for funk or slap-
style playing.
TIP: It is easiest to adjust the MIDRANGE when the LEVEL
control is at its maximum or minimum, so that the effect
of the FREQUENCY knob is more easily heard. Once the
proper FREQUENCY setting is found, adjust the LEVEL
knob to the desired setting.
J. FX LOOP — Connect the SEND to the input of outboard
effects devices (delay, chorus, etc.) and the output of the
effects devices to the RETURN. Placing effects in the
FX LOOP (instead of between your bass and the INPUT)
will reduce the amount of noise and tone degradation
caused by the effects pedals.
TIP: You can connect the SEND jack to other devices
(such as tuners, or additional power amplifiers) without
connecting signal back to the RETURN jack. Returning
signal to the RETURN jack is not required for operation
of the amplifier. Additionally, you can connect external
signals to the RETURN jack to bypass the preamp controls,
and send external signal directly to the power amplifier.
WARNING: WARNING:
FENDER AMPLIFIER SYSTEMS ARE CAPABLE OF PRODUCING MAINTAIN 6" CLEARANCE FOR VENTILATION.
VERY HIGH SOUND PRESSURE LEVELS WHICH MAY CAUSE
CAUTION:
TEMPORARY OR PERMANENT HEARING DAMAGE. USE CARE
TO REDUCE THE RISK OF FIRE, REPLACE
WHEN SETTING AND ADJUSTING VOLUME LEVELS DURING USE.
FUSE WITH SAME TYPE AND RATING
E F F E C T S L O O P
ATTENTION:
4½ min TOTAL F X
UTILISER UN FUSIBLE DE RECHANGE
DE MEME TYPE ET CALIBRE
150W
PARALLEL HEAD FOOT
SPEAKER OUTPUTS SEND RETURN AUX IN PHONES SWITCH
A PRODUCT OF:
F E N D E R M U S I C A L
INSTRUMENTS CORP.,
CORONA, CA U.S.A.
MADE IN CHINA
GROUND
LIFT
LINE OUT