NEWHOUSE HARDWARE MCHBV Instrucciones De Instalación

TWO NOTE MECHANICAL
DOOR CHIME
Installation Instructions and Drill Template.
Read and save these Instructions.
The non-electric chime mounts directly through the door
MODEL: 29
and will accommodate door thicknesses of ¾" to 2".
Installation Instructions and Drill Template.
LOCATING THE DOOR CHIME
Read and Save these Instructions.
• The non-electric chime mounts directly
1. Mount the chime in the center of the door
through the door and will accommodate
approximately 4½ to 5 feet above the floor.
door thicknesses of 3/4" to 2".
2. Using the template provided, mark the
• The chime is equipped with a viewer.
location of the mounting holes parallel to the edge of the
LOCATING THE DOOR CHIME
door (see Figure 1). Note: it is important that the holes are
1. Mount the chime in the center of the door
parallel to the edge of the door for proper operation of the
approximately 4 1 / feet to 5 feet above
2
chime.
the floor. Note: Be sure there are no
3. Drill two 1"holes parallel to the edge of the door.
obstructions on the inside of the door to
4. Drill three pilot holes using a 1/16 drill bit. interfere with the chime's baseplate.
2. Using the template provided, mark the
location of the mounting holes parallel
PUSH BUTTON ASSEMBLY to the edge of the door (see Figure 1).
Note: It is important that the holes are
See Figure 1 for push button assembly.
parallel to the edge of the door for
Note: If push button assembly is located in
proper operation of the chime.
3. Drill two 1" holes parallel to edge of an area that is exposed to rain, caulk around the
door.
1" holes before attaching the push button to the door.
4. Drill three pilot holes using a 1/16" drill
bit.
Please note: this door chime works best for smaller homes,
apartments, studios or offices. It may be difficult to hear this
chime from further than 30 feet away.
Door Edge
Viewer
Name Card
Name Card Holder
Metal Trim
Trim Screw
Figure 1 - Attaching Push Button Assembly to Door
ATTACHING PUSH BUTTON ASSEMBLY
1. Remove metal trim screw, metal trim, name
card holder and name card from push button
assembly to locate mounting holes (see Figure 1).
2. Insert viewer and push button shaft into
Two-Note Non-
pre-drilled until push button assembly is flush
against door face. Attach using the three
Electric Door Chime
mounting screws provided (see figure 1).
– With Viewer
3. Print or type name and address on name card
(provided). Place card in holder with printing
PUSH BUTTON ASSEMBLY
visible through front of card holder.
See Figure 1 for push button assembly.
4. Place metal trim over push button assemble
Note: If push button assembly is located in
and name card holder. Secure trim with trim
an area that is exposed to rain, caulk
screw (see Figure 1).
around the 1" holes before attaching push
button to door.
MOUNTING CHIME ASSEMBLY
ATTACHING PUSH BUTTON
1. Position chime assembly over push button shaft
ASSEMBLY
and viewer (see Figure 2).
1. Remove metal trim screw, metal trim,
2. Verify chime assembly is parallel to edge of door.
name card holder, and name card from
3. Attach the top and bottom of chime assembly
push button assembly to locate mount-
securely using mounting screws provided
ing holes (see Figure 1).
(see Figure 2).
2. Insert viewer and push button shaft
into predrilled until push button as-
sembly is flush against door face. At-
tach using the three mounting screws
provided (see Figure 1).
3. Print or type name and address on
name card (provided). Place card in
holder with printing visible through front
of card holder.
4. Place metal trim over push button as-
sembly and name card holder. Secure
trim with trim screw (see Figure 1).
1" Viewer Hole
1" Shaft Hole
1/16" Pilot Hole
Push Button Shaft
Push Button Assembly
Mounting Screw
MOUNTING CHIME ASSEMBLY 3. If necessary, adjust one or both as-
semblies.
1. Position chime assembly over push
button shaft and viewer (see Figure 2).
ATTACHING CHIME COVER
2. Verify chime assembly is parallel to
1. To insure proper clearance when the
edge of door.
cover is attached, break off the excess
3. Attach the top and bottom of chime
push button shaft. IMPORTANT: To
assembly securely using mounting
avoid breaking plastic chime assem-
screws provided (see Figure 2).
bly parts, use needle-nosed pliers to
OPERATION
hold shaft securely while bending shaft
back and forth to remove (see Figure Questions? Please contact us at
1. Verify door chime operation by press-
2, View A).
ing push button. The chime will sound
cs@adamaxinc.com
2. Place slot in chime cover over tab on
two (2) notes.
top of chime assembly.
2. If door chime does not operate prop-
3. Press bottom of chime cover onto
erly, check push button and chime
chime assembly until cover "snaps"
assemblies. Both assemblies must be
into place.
parallel to the door edge for proper
chime operation.
Push Button
Assembly (Shown
on Outside of Door)
Needle-Nosed Pliers
Cover Mounting Tab
Break Off Excess
Push Button Shaft
Chime Assembly
Mounting Screws
Figure 2 - Mounting Chime Assembly and Attaching Chime Cover
OPERATION
1. Verify door chime operation by pressing push
button. The chime will sound two notes.
2. If door chime does not operate properly,
check push button and chime assemblies. both
assemblies must be parallel to the door edge for
proper chime operation.
3. If necessary, adjust one or both assemblies
ATTACHING CHIME COVER
1. To insure proper clearance when the
cover is attached, break off the excess
push button shaft. IMPORTANT: To avoid
breaking plastic chime assembly parts, use
needle-nosed pliers to hold shaft securely
while bending shaft back and forth to
remove (see Figure 2 View A)
2. Place slot in chrome cover over tab on
top of chime assembly.
3. Press bottom of chime cover onto chime
assembly until cover snaps into place.
VIEWER HOLE
1 1 / "
8
Cover
1
View A 1 / "
16
Mounting
Slot
Chime Cover
PUSH BUTTON
SHAFT HOLE
1" DIA.
Model
MCHBV
(TOP)
MODEL 29
MOUNTING TEMPLATE
1/16" PILOT HOLES
(3 LOCATIONS)
1" DIA.
MOUNT
4 1 / - 5 ft.
2
ABOVE BOTTOM
OF DOOR
1 7 / "
8
3 /
16
15
/ "
16
"