Specified Conditions Of Use; Ec Declaration Of Conformity - Milwaukee M18 FNCS18G Manual Original

Keep hands and body parts clear of immediate work area. Hold
workpiece with clamps when necessary to keep hands and body
out of potential harm. Be sure the workpiece is properly secured
before pressing the fastener against the material. The workpiece
contact may cause the work material to shift unexpectedly. Keep
face and body parts away from back of the tool cap when working
in restricted areas. Sudden recoil can result in impact to the body,
especially when nailing into hard or dense material.
During normal use the tool will recoil immediately after driving a
fastener. This is a normal function of the tool. Do not attempt to
prevent the recoil by holding the stapler against the work.
Restriction to the recoil can result in a second fastener being
driven from the stapler. Grip the handle fi rmly, let the tool do the
work and do not place second hand on top of tool or near exhaust
at any time. Failure to heed this warning can result in serious
personal injury.
Do not drive fasteners on top of other fasteners or with the tool at
an overly steep angle as this may cause defl ection of fasteners
which could cause injury.
Always check the work area for hidden wiring, gas lines, water
lines, etc., before using the product on such work area.
After using the product in the contact actuation mode, switch it
back to the full sequential mode.
The driving depth of the nail may be adjusted beyond air pressure.
It is advisable to test the depth on a scrap workpiece to determine
the required depth for the application.
Only fasteners matching the description in the Technical Data can
be used with this tool. Using incorrect fasteners may lead to
jamming or other malfunctions.
Do not select contact actuation mode when working on scaff olds,
ladders or platforms where you may need to move your body
position. You may unintentionally fi re a nail by inadvertent
activation of the workpiece contact while moving about if the
contact actuation mode is selected. When moving positions, select
full sequential activation or deactivate the product completely by
removing the battery pack. This will reduce the potential for injury
to yourself and others.
Do not dispose of used battery packs in the household refuse or by
burning them. Milwaukee Distributors off er to retrieve old batteries
to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
Use only 18 V chargers for charging 18 V battery packs. Do not
use battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it off immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
Warning! To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in fl uid or allow a fl uid to fl ow inside them.
Corrosive or conductive fl uids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc., can
cause a short circuit.

SPECIFIED CONDITIONS OF USE

The stapler is intended for driving staples into wood or similar soft
materials from a magazine containing a strip of suitable nails. The
staple strip which can be safely loaded into the magazine for the
product are described in the product specifi cation table in this
manual. Do not use any other type of staple or fi xing with the
Stapler. The Stapler should not be used for fi xing electric cables.
Do not use this product in any other way as stated for normal use.
470 328 - M18FNCS18G.indd 27 470 328 - M18FNCS18G.indd 27
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant provisions
of the directives 2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC
and the following harmonized standards have been used:
EN 60745-1:2009+A11:2010
EN 60745-2-16:2010
EN 55014-1:2017
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-01-13
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess removeof 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure to heat
or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, after use, the battery packs have to be
fully charged.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
"For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and
away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in accordance
with local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated
to prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
OPERATION
There are two ways for working with this stapler (see also picture
section):
Single Sequential Actuation:
Drive the fastener by pulling the trigger.
Contact (Bump) Actuation:
Hold the trigger and drive the fastener by pushing the stapler
against the workpiece.
ENGLISH 27
17.01.2020 12:58:26 17.01.2020 12:58:26