Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
90521013 VPX Inflator manual
GENERAL SAFETY RULES
WARNING! Read all instructions before operating product. Failure to follow
all instructions listed below may result in electric shock, fire and/or serious
injury.
• KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
• CONSIDER WORK AREA ENVIRONMENT. Don't expose power tools to rain. Don't
use power tools in damp or wet locations. Keep work area well lit. Do not use tool in
presence of flammable liquids or gases.
• GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces.
For example; pipes, radiators, ranges, and refrigerator enclosures.
• KEEP CHILDREN AWAY. Do not let visitors contact tool or extension cord. All visitors
should be kept away from work area.
• STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or
locked-up place — out of reach of children.
• DON'T FORCE TOOL. It will do the job better and safer at the rate for which it was
intended.
• USE RIGHT TOOL. Don't force small tool or attachment to do the job of a heavy-duty
tool. Don't use tool for purpose not intended.
• DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in
moving parts. Rubber gloves and non-skid footwear are recommended when working
outdoors. Wear protective hair covering to contain long hair.
• USE SAFETY GLASSES. Also use face or dust mask if operation is dusty.
• DON'T ABUSE CORD. Never carry tool by cord or yank it to disconnect from
receptacle. Keep cord from heat, oil, and sharp edges.
• SECURE WORK. Use clamps or a vise to hold work. It's safer than using your hand
and it frees both hands to operate tool.
• DON'T OVERREACH. Keep proper footing and balance at all times.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories. Inspect tool
cords periodically and if damaged, have repaired by authorized service facility. Inspect
extension cords periodically and replace if damaged. Keep handles dry, clean, and free
from oil and grease.
• DISCONNECT OR LOCK OFF TOOLS when not in use, before servicing, and when
changing accessories, such as blades, bits, cutters.
• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that
keys and adjusting wrenches are removed from tool before turning it on.
• AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure
switch is off when plugging in.
• EXTENSION CORDS. Make sure your extension cord is in good condition. When using
an extension cord, be sure to use one heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in line voltage resulting in loss of power
and overheating. The following table shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord.
Volts
120V
240V
Ampere Rating
More
Than
0
-
6
-
10
-
12
-
7/31/07
10:47 AM
SAVE THESE INSTRUCTIONS
Minimum Gage for Cord Sets
Total Length of Cord in Feet
0-25
26-50
51-100
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
0-50
51-100
101-200
(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)
Not more
American Wire Gage
Than
6
18
16
16
10
18
16
14
12
16
16
14
16
14
12
Not Recommended
2
Page 2
101-150
201-300
14
12
12
Publicidad
Tabla de contenido
