Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
English
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.
Wall Mounting
Some D
WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
SPECIFICATIONS
Maximum Pounds per Square Inch
Rated Gallons per Minute
Battery
Inlet Hose
Pressure of Inlet Water
Inlet Water
Soap Consumption Rate
10
Attaching Quick Connect Filter (Fig. D)
This power cleaner must be used with the quick connect
adapters. The garden or suction hose can only be attached
when the quick connect filter
1. To connect the quick connect filter
To Attach the Spray Wands, Soap Bottle or
other Attachment (Fig. E)
The spray wand, soap bottle and other attachments (sold
seperately) connect to the power cleaner. To connect the
spray wand
•
•
nOTE: Other accessories are available for use with this power
cleaner, refer to the Accessories section.
To Attach the Garden or Suction Hose
(Fig. F, G)
Connecting the garden hose or suction hose will depend on
the job to be performed.
To Attach Garden Hose (Fig. F)
This power cleaner must be used with the quick
connect adapters.
1. To connect the quick connect hose adapter
550
2. To connect the quick connect hose adapter
1.0
20V DC
20 ft (6 m)
20-100 PSI
Cold Tap
3. Always disconnect the garden hose after usage. To
10% MAX
7
cleaner
2
, place the end of the quick connect filter onto
the water intake
3
. Tighten the quick connect filter
by hand.
nOTE: Avoid cross threading when installing the hose.
Cross threading will cause leaks.
8
and soap bottle
11
Insert the end of the attachment into the opening on
the power cleaner
. Push in and turn the attachment
2
clockwise until its secured into working position.
To remove the attachment, push in and turn the
attachment counterclockwise and pull from the power
cleaner
2
.
garden hose, thread the quick connect hose adapter
onto the end of the garden hose. Tighten the garden
hose by hand.
nOTE: Avoid cross threading when installing the hose.
Cross threading will cause leaks.
nOTE: Before connecting the garden hose to the
power cleaner, run water through the garden hose for
thirty seconds to clear any debris from the mouth of
the garden pressure hose.
quick connect filter
7
on the power cleaner
the quick connect hose adapter firmly onto the quick
connect filter.
nOTE: Before use, gently tug on the garden hose to
ensure the connection is secured. Make sure the quick
connect hose adapter is flush with the quick connect
filter as shown in Figure F.
disconnect, pull back the collar on the quick connect
hose adapter and remove from the quick connect filter.
is installed.
7
to the power
to the power cleaner
2
.
16
to a
16
to the
2
, push
Publicidad
Tabla de contenido
