Samsung 3 Serie Manual Del Usuario página 30

Other Information
Issues
No Picture, No Video
The TV won't turn on.
The TV turns off automatically.
There is picture/Video.
RF(Cable/Antenna) Connection
The TV is not receiving all channels.
The picture is distorted: macroblock error
small block, dots, pixelization
PC Connection
A "Not Supported Mode" message
appears.
"PC" is always shown on the source list,
even if a PC is not connected.
The video is OK but there is no audio.
Others
The picture won't display in full screen.
The remote control does not work.
The cable/set top box remote control
doesn't turn the TV on or off, or adjust the
volume.
A "Not Supported Mode" message
appears.
There is a plastic smell from the TV.
The TV Signal Information is unavailable
in the Self Diagnostic Test menu.
The TV is tilted to the side.
There are difficulties assembling the stand
base.
The channel menu is greyed out.
(unavailable)
30
English
Solutions and Explanations
• Make sure the AC power cord is securely plugged in to the wall outlet and the TV.
• Make sure the wall outlet is working.
• Try pressing the POWER button on the TV to make sure the problem is not the remote. If the TV turns
on, refer to "The remote control does not work" below.
• Ensure the Sleep Timer is set to Off in the Setup menu. (P. 19)
• If your PC is connected to the TV, check your PC power settings.
• Make sure the AC power cord is plugged in securely to the wall outlet and the TV.
• When watching TV from an antenna or cable connection, the TV will turn off after 10 ~ 15 minutes if
there is no signal.
• Check cable connections (remove and reconnect all cables connected to the TV and external
devices).
• Set your external devices' (Cable/Set top Box, DVD, Blu-ray etc) video outputs to match the
connections to the TV input. For example, if an external device's output is HDMI, it should be connect
to an HDMI input on the TV.
• Make sure your connected devices are powered on.
• Be sure to select the TV's correct source by pressing the SOURCE button on the TV remote.
• Make sure the Antenna cable is connected securely.
• Please try Plug & Play (Initial setup) to add available channels to the channel list. Go to MENU -
Setup - Plug & Play (Initial setup) and wait for all available channels to be stored.
• Verify the Antenna is positioned correctly.
• Compression of video contents may cause picture distortion, especially with fast moving pictures
such as sports and action movies.
• A low signal can cause picture distortion. This is not a TV issue.
• Set your PC's output resolution and frequency so they match the resolutions supported by the TV. (P.
9)
• This is normal; "PC" is always shown on the source list, regardless of whether a PC is connected.
• If you are using a HDMI connection, check the audio output setting on your PC.
• HD channels will have black bars on either side of the screen when displaying upscaled SD (4:3)
contents.
• Black bars on the top and bottom will appear during movies that have aspect ratios different from
your TV.
• Adjust the picture size options on your external device or TV to full screen.
• Replace the remote control batteries with the poles (+/–) in the right direction.
• Clean the sensor's transmission window on the remote.
• Try pointing the remote directly at the TV from 5~6 feet away.
• Programme the Cable/Set top box remote control to operate the TV. Refer to the Cable/Set user
manual for the SAMSUNG TV code.
• Check the supported resolution of the TV, and adjust the external device's output resolution
accordingly. Refer to the resolution settings on page
• This smell is normal and will dissipate over time.
• This function is only available with digital channels from an Antenna / RF/Coax connection. (P. 21)
• Remove the base stand from the TV and reassemble it.
• Make sure the TV is placed on a flat surface. If you can not remove the screws from the TV,
unnecessary use a magnetized screw driver.
• The Channel menu is only available when the TV source is selected.
9 of this manual.