Beta 1972/12 Manual Original página 16

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 24
TECHNICAL DATA
Production code............................................................................
Drilling capacity in steel ................................................................
Drilling capacity in wood ...............................................................
Wood screws (without pre-drilling) ...............................................
No-load speed, 1st gear ...............................................................
No-load speed, 2nd gear ..............................................................
Torque * (1.5 Ah / 2.0 Ah) .............................................................
Battery voltage..............................................................................
Drill chuck range ...........................................................................
Weight according EPTA-Procedure 01/2003 (1.5 Ah / 2.0 Ah) .....
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ..........................
Sound power level (Uncertainty K=3dB(A)) ...............................
Always wear ear protectors!
Total vibration values (vector sum in the three axes) determined
according to EN 60745.
Vibration emission value ah
Drilling into metal .......................................................................
Uncertainty K .............................................................................
Screwing ....................................................................................
Uncertainty K .............................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN
60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
DRILL SAFETY WARNINGS
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring.
Cutting accessory contacting a „live" wire may make exposed
metal parts of the power tool „live" and could give the operator
an electric shock.
SCREWDRIVER SAFETY WARNINGS
Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring. Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give the
operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust protection
mask.
Do not machine any materials that present a danger to health
(e.g. asbestos).
16
ENGLISH
CORDLESS DRILL DRIVER
1972/12
.......................4478 68 02...
...000001-999999
.............................10 mm
.............................20 mm
...............................6 mm
....................... 0-350 min
-1
..................... 0-1500 min
-1
.............................34 Nm
.............................12 V
.............................10 mm (3/8")
............................1,1 kg
..........................67,5 dB (A)
..........................78,5 dB (A)
............................1,6 m/s
2
............................1,5 m/s
2
............................0,9 m/s
2
............................1,5 m/s
2
Switch the device off immediately if the insertion tool stalls! Do
not switch the device on again while the insertion tool is stalled,
as doing so could trigger a sudden recoil with a high reactive
force. Determine why the insertion tool stalled and rectify this,
paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is
running.
When working in walls ceiling, or floor, take care to avoid
electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household refuse
or by burning them.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System PCLS chargers for charging System PCLS
battery packs. Do not use battery packs from other systems.

Publicidad

Tabla de contenido
loading

Tabla de contenido