Shindaiwa SP20HPS Guia Del Usuario

WARNING!
Hazard: Improper use or failure to follow instructions can result in explosive failure causing serious eye
or other injury. For safe use of this product you must read and follow all instructions. Do not leave a pressur-
ized sprayer in the hot sun. Heat can cause pressure build-up. Do not store or
Always wear goggles, gloves, long sleeve shirt, long pants and full foot protection when spraying. Never use
any tool to remove pump if there is pressure in sprayer. Never stand with face or body over
pumping or loosening pump to prevent ejecting pump assembly and/or solution from striking and injuring
you. Never pressurize sprayer by any means other than the original pump. Do not attempt to modify or repair
this product except with original manufacturer's parts. Never spray flammable materials or heat, pressure, or
gas producing chemicals. Always read and follow manufacturer's instructions before filling this sprayer as
some chemicals may be hazardous when used with this sprayer.
Handling the brass parts of this product will expose you to lead,
WARNING:
a chemical known to the State of California to cause birth defects and other
reproductive harm. Wash hands after handling.
Parts, Piezas, Pièces
569012 569011 569010
Flat Fan Nozzle Brass Adjustable Nozzle Poly Adjustable Nozzle
Tobera Tobera Tobera
Buse Buse Buse
569013
569006
Nozzle Kit
569007
Shut-off Assembly
Tobera
Unidad de cierre Hose Assembly
Buse
Assemblage d'arrêt Ensamblaje de la manguera
Assemblage de boyau
569008
Extension wand, Vara de extensión, Lance de rallonge
O-ring (1)
Anillo en "o" (1)
569015
Anneau torique (1)
Repair Kit
Juego de reparación
Kit de réparation
"C" Clip
Clip de "C"
Clip de « C »
569005 Elbow O-ring
Shut-off Valve Repair Kit
Kit de reparación para la válvula de cierre.
Trousse de réparation de robinet d'arrêt.
Nozzle Gasket
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
1. Hose to Tank
1A
Outlet
Tube
leave solution in tank after use.
Outlet Tube
top of tank when
Adapter
No
Outlet Tube
1D
Gap Adapter
Tab/
Tank Notch
Adapter
Discharge/ Assembly
• Make sure white outlet tube is attached to outlet tube adapter (Fig. 1A).
• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1B).
• Proper placement of white outlet tube (Fig. 1C).
• Firmly insert the outlet tube adapter into the tank adapter (Fig. 1D) Lining up tab
with notches on the tank adapter.
• Firmly tighten the retaining nut to the tank adapter (Fig. 1E).
2. Assembly of Shut-off, Extension Wand and Nozzle
2a
Shut-off Assembly
1) Screw nozzle assembly onto threaded end of the extension wand securely.
2) Insert unthreaded end of extension wand into shut-off assembly as shown and tighten retaining
nut securely.
Model# SP20HPS
Nozzle Assembly
Figure 1-2
Unscrew the nozzle cap (1) from the nozzle body (3) with retaining nut (2) fastened tightly to the elbow (5). Unscrew the
retaining nut (2). Push the nozzle body (3) with the nozzle gasket (4) out of the retaining nut (2). To reinstall the nozzle,
Hose Washer
569014
reverse the above instructions.
O-ring Kit
Kit del anillo "O"
Figure 3
Trousse de
Unscrew the retaining nut from the elbow and push the fan nozzle tip and gasket out of the retaining nut. To reinstall the
joint torique
Wand O-ring
nozzle, reverse the above instructions.
3. Filter
The filter helps prevent clogging while spraying. It is located on the end of the outlet tube inside your sprayer tank. To clean
filter, remove the discharge assembly from the tank (Fig.1B). Make sure the filter is positioned at the bottom of the tank as
pictured in figure (1C).
011311 (A) R0910
1C
Discharge
1B
Outlet
Assembly
Tube
1E
Retaining Nut -
Securely tightened.
Nozzle Assembly
Retaining Nut
Extension Wand
4. Fatigue-free spraying
LOCK-OFF POSITION LOCK-ON POSITION NEUTRAL POSITION
4a Locking Mechanism Handle
4c
4b
Down
Handle
Up
For safety lock-off feature (no-spraying), pull up on handle and move red locking mechanism into lock-off position as
shown in fig. 4a. To disengage, push down on handle and return red locking mechanismto neutral position as in fig. 4c.
For lock-on feature (continuous spraying), push down on handle and move red locking mechanism into lock-on position
as shown in fig. 4b. To disengage, push down on handle and return red locking mechanism to neutral position as shown in
fig. 4c.
If the handle fails to operate correctly, release the pressure from the tank by pressing the red pressure release button.
Inspect and repair the handle assembly or replace with a new handle assembly.
5. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose
before using. Replace with original manufacturer's parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for signs of
deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could result in
explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace. Do not attempt
to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.
5) Do: Pump plunger 10-20 strokes and inspect for leaks.
6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling,
Pressurizing and Spraying Instructions.
6. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
7. Pressurizing and Spraying
7A 7B
Do: Turn handle clockwise to Do: Pump until
tighten. Push handle down, you feel resistance.
turn 1/4 turn counterclockwise
to release.
8. To Release Pressure
1) Your sprayer is equipped with a pressure release button. To release
pressure press red button until air is completely exhausted.
2) Do: Point air flow away from you and others until air has escaped.
9. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing and Spraying
Instructions, except pump unit only 8-10 strokes.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
7C
Do: Push handle, down, turn 1/4 turn
clockwise to lock. Begin spraying. Re-pump
sprayer as required to maintain spray force.
8A