Safety Rules - Flymo Speedi-Mo 360VC Traducción De Las Instrucciones De Empleo Originales

IMPORTANT! Read before use and
retain for future reference.
WARNING!
!
If not used properly this product can
be dangerous! This product can cause
serious injury to the operator. Warn-
ings and safety instructions must be
followed to ensure reasonable safety
and effi ciency in using this product.
The operator is responsible for follow-
ing the warning and safety instructions
in this manual and on the product.
EXPLANATION OF WARNING LEVELS
The warnings are graded in three levels:
WARNING! Used if there is a risk of
!
serious injury or death for the operator
or damage to the surroundings if the
instructions in the manual are not
followed.
IMPORTANT! Used if there is a risk of
!
injury to the operator or damage to the
surroundings if the instructions in the
manual are not followed.
CAUTION! Used if there is a risk of damage to mate-
rials or the machine if the instructions in the manual
are not followed.
GENERAL
1 This product is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning the use of the product by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with
the product. Local regulations may restrict the age of
the operator.
2 Never allow children or people unfamiliar with the
instructions to use the machine.
3 Stop using the machine while people, especially
children, or pets are nearby.
4 Only use the product in the manner and for the
functions described in these instructions.
5 Never operate the product when you are tired, ill or
under the infl uence of alcohol, drugs or medicine.
6 The operator or user is responsible for accidents or
hazards occurring to other people or their property.
ELECTRICAL
1 The use of a Residual Current Device (R.C.D.) with
a tripping current of not more than 30mA is recom-

SAFETY RULES

mended. Even with a R.C.D., installed 100% safety
cannot be guaranteed and safe working practice
must be followed at all times. Check your R.C.D.
every time you use it.
2 Before use, examine the cable for signs of damage
or aging. If the cable is found to be defective, take
the product to an Authorised Service Centre and
have the cable replaced.
3 Do not use the product if the electric cables are
damaged or worn.
4 Immediately disconnect from the mains electricity
supply if the cable is cut, or the insulation is dam-
aged. Do not touch the electric cable until the elec-
trical supply has been disconnected. Do not repair a
cut or damaged cable. Replace it with a new one.
5 Your extension cable must be uncoiled. Coiled
cables can overheat and reduce the effi ciency of
your mower.
6 Keep cable away from product. Always work away
from the power point mowing up and down, never
in circles.
7 Do not pull cable around sharp objects.
8 Always switch off at the mains before disconnecting
any plug, cable connector or extension cable.
9 Switch off, remove plug from mains and examine
electric supply cable for damage or aging before
winding cable for storage. Do not repair a damaged
cable, replace it with a new one. Use only genuine
replacement cable.
10 Always wind cable carefully, avoiding kinking.
11 Never carry the product by the cable.
12 Never pull on the cable to disconnect any of the
plugs.
13 Use only on AC mains supply voltage shown on the
product rating label.
14 Our products are double insulated to EN60335. Un-
der no circumstances should an earth be connected
to any part of the product.
CABLES
If extension cables are used, they must comply with the
minimum cross-sections in the table below:
Voltage
220-240V/ 50Hz
220-240V/ 50Hz
1 Mains cables and extensions are available from your
local Approved Service Centre.
2 Only use extension cables specifi cally designed
for outdoor use and which conform to one of the
following specifi cations: Ordinary rubber (60245 IEC
53), Ordinary PVC (60227 IEC 53) or Ordinary PCP
(60245 IEC 57).
3 If the short connection lead is damaged, it must be
replaced by the manufacturer, its service agent or
similarly qualifi ed persons in order to avoid a hazard.
PREPARATION
1 While using your product always wear substantial
footwear and long trousers. Do not operate the
Cable length Cross section
Up to 20 m 1.5 mm
20 - 50 m 2.5 mm
English – 5
2
2