Steren LAM-227 Manual De Instrucciones

Before using your new Steren LED & magnifier SOS lamp,
please read this instruction manual to prevent any damage.
Put it away in a safe place for future referen
IMPORTANT
• Do not expose your equipment to extreme temperatures.
• Always use a smooth, clean and dry cloth to clean the equipment.
• When the lamp remains without use for long periods of time, make sure to
remove the batteries.
1. Lamp.
2. ON/OFF button.
3. Battery compartment.
4. Strap.
BATTERY INSTALLATION
Front lamp
1. Unscrew the battery top.
2. Take out the battery container.
3. Place 3 batteries type AAA inside the battery compartment. Pay attention
in the polarity.
4. Insert the battery container into the lamp following the arrow direction.
Back lamp
1. Lift up the lamp top to lever, first pull up from one side.
2. Carefully remove the two plastic parts on the battery compartment.
3. Place 2 batteries type AAA inside the battery compartment. Pay attention
in the polarity.
4. Introduce the two plastic parts again and close the lamp top.
NOTE: Take care that the seal stays in place.
OPERATION
Forward lamp´s support
1. Loose the upper screw from the support
for introduce the forward lamp. Make sure
to introduce the strap first.
2. Push the lamp inside the support.
3. Screw again making sure that the lamp
does not get out.
4. To place the support on the handlebar,
totally remove the lower screw to allow a
wide opening.
5. Introduce the handlebar in the opening.
6. Screw again the support making sure that
the lamp is not moving.
PARTS
7. Turn on the light.
If you press the button once, the lamp will light continuous.
If you press the button twice, the lamp will turn off.
Back lamp´s support
1. Remove the screw on the right side of the support.
2. Place the support in the stem and arrange the support in
the height you wish.
3. Screw very well making sure that the support is not moving.
4. Identify the back clip on the lamp.
5. Identify the clip in the lamp´s support.
6. Place the clip lamp´s support on the lamp´s clip. Bottom-up
slide, and hear "click" that indicating that the lamp is secure.
7. Turn on the light.
If you press the button once, the lamp will light continuous.
If you press the button twice, the lamp will light slowly.
If you press the button thrice, the lamp will turn on and off quickly.
If you press the button four times, the lamp will turn off.
TROUBLESHOOTING
The lamp does not light
SPECIFICATIONS
Lantern
Input: 4.5V (3xAAA)
Nominal consumption: 816 Wh/day
Stand-by power consumption: not
applicable
Before using your new Electronic insect killer, please read this
Product design and specifications are subject to change
instruction manual to prevent any damage. Put it away in a
without previous notice.
Product: Bike LED lamp set
Part number: LAM-227
Brand: Steren
This Steren product is warranted under normal usage against defects in
workmanship and materials to the original purchaser for one year from the
date of purchase.
CONDITIONS
1.- This warranty card with all the required information, invoice or purchase
ticket, product box or package, and product, must be presented when
warranty service is required.
2.- If the product stills on the warranty time, the company will repair it free
of charge.
3.- The repairing time will not exceed 30 natural days, from the day the
claim was received.
4.- Steren sell parts, components, consumables and accessories to
customer, as well as warranty service, at any of the addresses mentioned
later.
THIS WARRANTY IS VOID IN THE NEXT CASES:
If the product has been damaged by an accident, acts of God, mishandling,
leaky batteries, failure to follow enclosed instructions, improper repair by
unauthorized personnel, improper safe keeping, among others.
a) The consumer can also claim the warranty service in the purchase
establishment.
b) If you lose the warranty card, we can reissue it, if you show the invoice
or purchase ticket.
In case your product fails or have questions,
please contact your nearest dealer.
If you are in Mexico, please give a call to our Call Center.
Call Center 01 800 500 9000
- Press the button on and off.
- Check the battery polarity.
- Replace batteries.
Preventive
Input: 3V (2xAAA)
Nominal consumption: 233 Wh/day
Stand-by power consumption: not
applicable
WARRANTY