Preparing To Work; Inserting The Filter - Collection Bag; Work; Starting Work - bluematic CUBE Manual De Uso

Before beginning to work, it is necessary to:
1. Before using, the appliance must be in order and safe to use with the work
equipment, especially the power cable and the extension cable. If everything
is not in order, the appliance must not be used.
2. Insert the suction tube (1) into the suction nozzle (3) in the collection barrel,
turning the sleeve (2).(Fig.11).
3. If not present in the appliance, insert a new filter - new collection bag (read
the section "INSERTING A FILTER - COLLECTION
To insert the filter – collection bag inside the collection tank, proceed as follows:
1. Take all necessary steps to ensure that the device is in a safe condition (see
"MACHINE SAFETY").
2. To open the aspirator pull the lever (2) in the direction indicated by the
arrow(Fig.12).
3. Using the handle (3), in the vacuum tank lid (Fig.13), remove the vacuum
tank lid from the collection tank (rotating it and shifting it as indicated in the
figure13). Put the vacuum tank lid gently on the floor.
To insert the power cable of the appliance, carry out the following:
1. Lock the power cable (1) inside the cable stop (3) (Fig. 16)
2. Insert the quick connector of the cable (1) into the power socket (2) on the upper part of the vacuum cleaner.
To start working, proceed as follows:
1. Make all the checks listed in "PREPARING TO
2. Insert the plug (2) of the power supply cable (3) in the mains supply socket
(4) (Fig.10).
3. Turn on the appliance by pressing the main switch (1) (Fig.17).
4. If the "combined nozzle" accessory is used, set the switch in the brush to
"HARD SURFACE" or else "CARPETS". Proceed with the vacuuming.
If while working you note that the vacuum accessory is sticking to much to the
At the end of the work, and before carrying out any type of maintenance,
perform the following operations:
1. Take the appliance to the place where it is maintained and carry out all the
procedures listed in the chapter
2. Take the appliance to the designated machine storage place.
3. Do what is required to make sure the appliance is in a safe condition (see
"APPLIANCE SAFETY").
4. Insert the suction tube fixing clip in the support (3) in the rear part of the
TYPE OF MAINTENANCE
Cleaning accessories
Checking and cleaning inlet air filters and drain filter
Replacing the power cable
Replacing the collection bag filter

PREPARING TO WORK

PREPARING TO WORK
BAG").
INSERTING THE FILTER – COLLECTION BAG
POWER SUPPLY CABLE CONNECTION

WORK".

AT THE END OF THE WORK

"DAILY

MAINTENANCE".

SCHEDULED MAINTENANCE OPERATIONS

X
4. Select the most suitable accessory for the work to be carried out.
5. Insert the selected accessory into the vacuum hose.
6. If not present in the appliance connect the power cable (read the section
"CONNECTING THE POWER
ATTENTION: never use the appliance without the filters supplied with
the machine (COLLECTION BAG-FILTER; INLET AIR FILTERS;
EXHAUST AIR FILTER).
4. Insert the paper collection bag filter inside the collection drum, making sure
to insert the filter correctly in its housing (4), inside the collection drum and
not to damage the cardboard support (6) present in the bag (5)(Fig.14).
5. Using the handle (3), position the upper part of the vacuum cleaner on the
collection barrel. Paying great attention to insert the two forks (7) on the
appropriate seat (8) present in the suction shaft (Fig.13).
6. Close the suction by pressing the closing lever (1) (Fig.4).
7. Re-attach the suction hose to the machine (Fig.11).
WORK

STARTING WORK

surface on which it is being used, adjust the air flow inside the vacuum hose
using the lever on the grip and free the accessory.
machine (Fig18)
ATTENTION: Park the appliance in an enclosed place, on a flat surface;
near the appliance there must be no objects that could either damage it,
or be damaged through contact with it.
MAINTENANCE
X
X X X
X
X
23
CABLE").