Hunter 19253 Instrucciones De Instalación

PREPARING FOR INSTALLATION
Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old
fixture from the wall, including the old mounting bracket. Remove the new mounting bracket assembly from the bag.
Then remove cap nuts (G) from mounting screws (E). Mounting plate (B) contains several pairs of threaded holes. Find
the pair of holes that matches the spacing of the holes on the fixture's backplate. Place the mounting plate (B) over the
junction box so that mounting screws (E) and nuts (D) are visible. Depending on the placement of your junction box
the position of mounting screws (E) may need to be adjusted to allow the backplate to be flush with the wall. Adjust
the position of mounting screws (E) so that mounting screws (E) can be exposed 5-6 mm after passing through the
backplate (F). Once the ideal position of mounting screws (E) has been confirmed, tighten nuts (D) on mounting screws
(E) on the front of the mounting plate to ensure that mounting screws (E) are in place. Pull the house wires through the
center of mounting plate (B). Secure mounting plate (B) to the junction box by tightening the screws (C).
FINISHING THE INSTALLATION
Place the fixture's backplate (F) over the mounting screws (E) so the threads protrude through the holes on the front of
the backplate. Tightly screw the cap nuts (G) onto the mounting screws (E) until the backplate (F) of the fixture is snugly
against the wall. Install light bulb (not included) in accordance with the fixture's specifications. Do not exceed the
recommended wattage.
Secure glass shade (J) onto the casting cover (H) with screws (I). Your installation is now completed. Turn on the power
and test the fixture.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light
and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.
CONNECTING THE WIRES
Have a helper support the fixture's weight while completing the
wiring. Attach the fixture's wires to the power supply wires from the
junction box. Connect black to black (Live); white to white (grounded);
grounding to grounding (green or copper). Twist the ends of the wire
pairs together. Then, twist on a wire connector. Make sure all twists are
in the same direction. Loop fixture's ground wire around grounding
screw (A) and tighten. If there is no ground wire (green or copper) from
the junction box, contact a qualified electrician.
ENGLISH
Cypress Grove
For Models:
Para los Modelos:
Pour les Modèles:
19253
19254
19351
Here are the
1
Light Vanity
tools you'll
1 Luz Decorativa de Pared
need to
1 Lumière Vanité
complete your
installation:
Estas son las Fixture weight ±2 lbs:
herramientas
Peso ±2 lb: 2.43 lbs (1.10 kg)
que usted
Poids fixe ±2 lbs:
necesitará para
completar su
instalación:
Voici les outils Hardware Service Kit/Kit De Mantenimiento Del Equipo/Trousse De
Maintenance Quincaillerie
dont vous
aurez besoin
Part #/Pieza #/Pièce # Model/Modelo/Modèle
pour réaliser
l'installation:
KD80701872 19253
KD80701632 19254
KD80701214 19351
Ladder
Glass/Domo De Vidrio/Verre
Escalera
Échelle Part #/Pieza #/Pièce # Model/Modelo/ Modèle
19253
19254
KD50401147 19351
INSTRUCCIONES DE INSTALACIÓN/ INSTRUCTIONS D'INSTALLATION
Screwdriver
Destornilladore
• WARNING
Tournevis
• To avoid possible electrical shock, before
installing your light fixture, disconnect the power
by turning off the circuit breakers to the outlet box
associated with the wall switch location.
• The lighting fixture must be grounded. If the
ground wire for the installation site is not present,
immediately STOP installation and consult a
Pliers
qualified electrician.
Alicates
• All wiring must be in accordance with national
Pince
and local electrical codes ANSI/NFPA 70. If you
are unfamiliar with wiring or in doubt, consult a
qualified electrician.
READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It
is very important that they are read carefully and
Wire Strippers
completely before beginning installation of the
Pelacables
lighting fixture.
Pince à dénuder
F
G
H
I
J
Finish/Finish/Fini
Natural Iron/Hierro Natural/
Fer Naturel
Onyx Bengal/Bengala Ónix/
Onyx du Bengale
Brushed Nickel/Níquel Pulido/
Nickel Brossé
Type/Tipo/Type
Clear Halophane Glass/Vidrio
Transparente Tipo Holophane/
Verre Holophane Transparent
INSTALLATION INSTRUCTIONS
•
ADVERTENCIA
• Para evitar una posible descarga eléctrica, antes
de instalar su lámpara, desconecte la energía
apagando los interruptores automáticos (breakers)
que alimentan la caja de salida asociada con la
ubicación del interruptor de pared.
• L'appareil d'éclairage doit être mis à la terre.
Si le fil de terre du lieu d'installation n'est pas
présent, ARRÊTEZ immédiatement l'installation et
consultez un électricien qualifié.
• Todo el cableado debe realizarse de acuerdo con
los códigos eléctricos locales y nacionales ANSI/
NFPA 70. Si no está familiarizado con el cableado,
o si tiene duda, consulte a un electricista calificado.
LEA Y GUARDE ESTAS INSTRUCCIONES
Estas instrucciones se proporcionan para su
seguridad. Es muy importante leerlas detenid-
amente y completamente antes de comenzar la
instalación de la lámpara.
©2021 Hunter Fan Co. ML080
R_051221
E
D
A
B
C
•
AVERTISSEMENT
• Pour éviter tout choc électrique, avant d'installer
le luminaire, coupez le courant en éteignant les
disjoncteurs de la boîte électrique associée à
l'interrupteur mural.
• Le luminaire doit être mis à la terre. Si le fil
de terre du lieu d'installation n'est pas présent,
ARRÊTER immédiatement l'installation et
consulter un électricien qualifié.
• Tout le câblage doit être conforme aux codes
électriques nationaux et locaux en vigueur et à la
norme ANSI/NFPA 70. Si vous n'avez pas l'habitude
de faire ce câblage ou en cas de doute, adressez-
vous à un électricien qualifié.
LISEZ ET CONSERVEZ CES INSTRUCTIONS
Ces instructions sont fournies pour votre sécurité.
Il est très important de les lire attentivement dans
leur intégralité avant d'entreprendre l'installation
du luminaire.