Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
H-1663
PLASTIC EXIT SIGN
TOOLS NEEDED
Flathead Screwdriver
CAUTION! When using electrical equipment,
basic safety precautions should always be
followed, including:
• Do not use outdoors.
• Do not mount near gas or electric heaters.
• Do not let power cords touch hot surfaces.
• Use caution when servicing batteries. Avoid
possible shorting.
• Equipment should be mounted in locations
and at heights where it will not readily be
subjected to tampering by unauthorized
personnel.
BACK MOUNTING
1.
Drill 1/4" holes into oblong knock outs on back plate
that correspond to junction box holes to be used.
(See Figure 1)
Figure 1
Wire Nuts
EXIT Panel
PAGE 1 OF 6
1-800-295-5510
uline.com
Phillips Screwdriver
INSTALLATION
Junction
Box
Back Plate
Plastic
Housing
Diffuser
Snap-in
Directional Arrow
SAFETY
• The use of accessories not recommended
by the manufacturer may cause an unsafe
condition.
• Do not use this equipment for anything other
than intended use.
• Before wiring to AC service, turn off AC power
at fuse or circuit breaker.
• Disconnect AC power and unplug battery
before servicing.
• Only use specified lamps in the fixture.
• Battery in this unit may not be fully charged.
After the AC service is supplied to the unit, let
the battery charge for at least 24 hours before
performing any tests.
2. Feed the transformer input leads through center
hole and make the proper connections. If using
120VAC, connect the black and white leads to the
building utility. If using 277VAC, connect the orange
and white leads to the building utility. Cap off
unused wire. If the unit is self-powered, be sure to
snap battery connector together.
3. Feed excess wire into junction box and secure back
plate to junction box. (See Figure 1)
4. Snap in arrows on EXIT panel as required. Then snap
EXIT panel to housing: top first, then bottom.
(See Figure 1)
NOTE: Use flexible
conduit only.
(See Figure 2)
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
Figure 2
0621 IH-1663
Publicidad
Manuales relacionados para Uline H-1663
Resumen de contenidos para Uline H-1663
- Página 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-1663 1-800-295-5510 uline.com PLASTIC EXIT SIGN TOOLS NEEDED Flathead Screwdriver Phillips Screwdriver SAFETY CAUTION! When using electrical equipment, • The use of accessories not recommended basic safety precautions should always be...
-
Página 2: Side Mounting
Use Manual Battery Test Switch on base of unit 0 2 3 3 4 5 6 Connector to test. Red LED indicates normal operation. Manual Battery (See Figure 8) Test Switch Red LED Socket 1-800-295-5510 PAGE 2 OF 6 0621 IH-1663 uline.com... -
Página 3: Herramientas Necesarias
H-1663 800-295-5510 uline.mx LETRERO DE PLÁSTICO "EXIT" HERRAMIENTAS NECESARIAS Desarmador de Desarmador de Cruz Cabeza Plana SEGURIDAD ¡PRECAUCIÓN! Hay ciertas medidas básicas • El uso de accesorios no recomendados por que deben seguirse al utilizar equipos el fabricante podría causar situaciones no eléctricos, incluyendo:... -
Página 4: Montaje Lateral
Batería manual ubicado en la base de la unidad Interruptor Manual de Prueba de Batería para hacer una prueba. El LED rojo indica un Orificio LED Rojo funcionamiento normal. (Vea Diagrama 8) 800-295-5510 PAGE 4 OF 6 0621 IH-1663 uline.mx... -
Página 5: Enseigne " Exit " En Plastique
H-1663 1-800-295-5510 uline.ca ENSEIGNE « EXIT » EN PLASTIQUE OUTILS REQUIS Tournevis à tête plate Tournevis cruciforme SÉCURITÉ MISE EN GARDE! Lorsque vous utilisez de • N'utilisez pas cet équipement à d'autres fins l'équipement électrique, vous devez toujours que celles prévues. prendre des précautions de sécurité de base, •... -
Página 6: Fixation Au Plafond
Emboîture manuel sur la base de l'unité pour vérifier son à DEL rouge fonctionnement. Le voyant à DEL rouge indique que l'unité fonctionne normalement. (Voir Figure 8) 1-800-295-5510 PAGE 6 OF 6 0621 IH-1663 uline.ca...