Package Contents - DeWalt D25413 Traducido De Las Instrucciones Originales

re-bar may be hazardous as well. Tighten the side handle
securely before use.
• Do not operate this tool for long periods of time.
Vibration caused by hammer action may be harmful to your
hands and arms. Use gloves to provide extra cushion and limit
exposure by taking frequent rest periods.
• Do not recondition bits yourself. Chisel reconditioning
should be done by an authorized specialist. Improperly
reconditioned chisels could cause injury.
• Wear gloves when operating tool or changing bits.
Accessible metal parts on the tool and bits may get extremely
hot during operation. Small bits of broken material may
damage bare hands.
• Never lay the tool down until the bit has come to a
complete stop. Moving bits could cause injury.
Do not strike jammed bits with a hammer to dislodge
•
them. Fragments of metal or material chips could dislodge
and cause injury.
• Slightly worn chisels can be resharpened by grinding.
• Keep the power cord away from the rotating bit. Do not
wrap the cord around any part of your body. An electric
cord wrapped around a spinning bit may cause personal
injury and loss of control.

WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.
Residual Risks
The following risks are inherent to the use of rotary hammers:
• injuries caused by touching the rotating parts or hot parts of
the tool.
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment of hearing.
• Risk of squeezing fingers when changing the accessory.
• Health hazards caused by breathing dust developed when
working in concrete and/or masonry.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your D WALT tool is double insulated in accordance
e
with EN60745; therefore no earth wire is required.

WARNING: 115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the
primary and secondary winding.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the D
service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1.5 mm
is 30 m.
When using a cable reel, always unwind the cable completely.

Package Contents

The package contains:
1 Heavy-duty rotary hammerdrill
1 Side handle
1 Depth adjustment rod (D25413, D25414, D25415 only)
1 Kitbox
1 Keyless chuck (D25414 and D25415 only)
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Date Code Position
The date code which also includes the year of manufacture, is
printed into the housing.
Example:
Description (Fig. A–D, F)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
WALT
e
Variable speed switch
1
Main handle
2
Forward / reverse slider
3
Mode selector
4
Safety lock
5
2 ; the maximum length
2017 XX XX
Year of Manufacture
EngLIsh
23