BOERBOEL Y-Latch Kit Instrucciones De Instalación página 2

WARNING:
• Improper installation of this product can result in personal injury. Always wear safety goggles when
cutting, drilling and assembling the product.
• Incorrect installation may cause harm to the gate or individual.
• Not pool code approved.
• Do not allow children to play with the gate.
NOTICE:
• DO NOT attempt to assemble the kit if parts are missing or damaged.
• DO NOT return the product to the store, for assistance or replacement parts call: 1-800-336-2383.
Component List:
QTY Description
1 Y-Latch
1 Stop Bracket
1" #2 Square/Phillips Combo
6
Self-Tapping Pan Head Screws
DOUBLE DRIVE GATE INSTALLATION
1
Determine Gate Opening:
Determine the gate opening by adding the width of the gates plus
clearance of hinges plus a clearance distance of 1-3/4" to 3" for
the Y-latch (Fig. 1). (See hinge instructions for clearance details.)
NOTE: Mount gate on hinges prior to installing the Y-latch.
2
Attach Y-Latch to Fence Gate:
Place and hold Y-latch on gate upright. Attach Y-latch to gate
upright with three self-tapping pan head screws (Fig. 2).
3
Determine Location of Stop Bracket:
While the swing arms are lowered and leveled, place stop bracket
at on the gate while moving the bracket up or down until the
swing arm is level. Once the swing arm is level, mark with a pencil
the stop bracket location on the side of the gate (Fig. 3).
4
Attach Stop Bracket to Gate:
With the gate opened, place stop bracket on the gate and align
with the pencil mark. Attach stop bracket to gate with the remaining
three self-tapping pan head screws (Fig. 4).
WALK GATE INSTALLATION
1
Determine Gate Opening:
Determine the gate opening by adding the width of the gate plus
clearance of hinges plus a clearance distance of 1-3/4" to 3" for
the Y-latch. (See hinge instructions for clearance details.)
NOTE: Mount gate on hinges prior to installing the Y-latch.
2
Attach Y-Latch to Fence Gate:
a. For walk gates utilizing 2" gate uprights and 2" post
uprights, the Y-latch can be installed in the same method
as the double drive gate installation (Fig. 5).
b. For walk gates utilizing 2" gate uprights and 2-1/2" post
uprights, the post will serve as the Y-latch swing arm stop.
NOTE: Do not install the stop bracket because it will not
t on post upright (Fig. 6).
PADLOCK OPTIONS
1
Fig. 3, 4 and 5 Y-latch installation should use padlock option 1
shown in Fig. 7.
2
Fig 6 Y-latch installation should use padlock option 2
shown in Fig. 7.
Y-Latch Kit
INSTALLATION INSTRUCTIONS
To obtain and review a copy of the warranty please go to: BoerboelGateSystems.com/warranty.
You can also contact 1-800-336-2383 or write to Boerboel Gate Solutions, 7830 Freeway Circle,
Middleburg Heights, Ohio 44130 to request a copy of the warranty.
BEFORE YOU BEGIN:
The primary design of the Y-latch
is for the aluminum double drive gates
with 2" uprights.
Gate
Upright
2"
Swing Arms
Stop Bracket
Screws
Fig. 1
MIN. SPACING 1.75"
MAX. SPACING 3.0"
Fig. 3
Fig. 5
TOOLS NEEDED:
Gate
#2 Square/Phillips Screwdriver
Safety Glasses
Tape Measure
Pencil
Drill
Arm Bracket
Fig. 2
Fig. 4
Fig. 6 Fig. 7
Padlock Option 1
Padlock Option 2