AmerTac TE08WHB Manual De Instrucciones Y Garantía

TE08WHB
Instruction Manual & Warranty
Indoor
8-Outlet Digital Power Strip Timer
8 Grounded Outlets, 4 Timer Controlled Outlets
INSTALLING BATTERY
1. Install a 1.5 volt "AG13" mercury battery in the battery compartment
on the back of the timer and then close the cover.
2. All of the display shows for three seconds, then the display
reads OFF MO 12:00 AM
3. The clock starts.
SETTING THE CURRENT TIME
While holding the CLK (CLOCK) button down, press the DAY, HR (HOUR)
and MIN (MINUTE) buttons to set the day of the week, hour and minutes
respectively.
PROGRAMMING EVENTS
1. Press the PROG button once. Display reads either:
- 1 ON MO TU WE TH FR SA SU --:-- , if it has not been set.
- 1 ON and previous setting, if it has previously been set.
The number 1 indicates that you are now programming event #1.
2. Press the DAY button repeatedly. The display shows the day on
which you want the timer to turn ON. The day options include:
- All days of the week (MO TU WE TH FR SA SU)
- Any single day of the week (MO TU WE TH FR SA SU)
- Weekdays only (MO TU WE TH FR)
- Weekends only (SA SU)
3. Press the HR (HOUR) and MIN (MINUTE) buttons to select the time
of day when you want the timer to turn ON.
4. Press the PROG button once again. Display reads:
- 1 OFF MO TU WE TH FR SA SU --:--, if it has not been set.
- 1 OFF and previous setting, If it has previously been set.
5. Repeat the procedure in steps 2 and 3 to select the day and time
when you want the timer to turn OFF.
6. If you choose to set multiple programs, repeat the procedures in
steps 1 to 5 to select the time and day when you want the timer
to turn ON and OFF for the other six events.
7. When programming is complete, press the CLK (CLOCK) button
to return to the current time display.
REVIEWING YOUR PROGRAMS
1. Press the PROG button repeatedly to check the ON and OFF
setting for each event.
2. While holding the MODE button down, press the PROG button
to clear the setting.
ACTIVATING YOUR PROGRAMS
1. Press the MODE button until the AUTO indicator is displayed.
The timer will operate automatically as programmed.
2. Press the MODE button until the RDM (RANDOM) indicator is
displayed. The timer will operate randomly as programmed. random
mode runs the programs you have set, but slightly varies the ON
and OFF times to reduce predictability and give the home a
more "lived-in" look.
MANUAL OVERRIDE
1. Press the MODE button until the ON indicator is displayed.
The outputs of the timer will turn ON and remain ON until
the mode is changed again.
2. Press the MODE button until the OFF indicator is displayed.
The outputs of the timer will turn OFF and remain OFF until
the mode is changed again.
OPERATING TIMER
1. Plug power strip into an outlet.
2. Plug device to be connected into one of the receptacles on the
power strip. Note that 4 outlets on left are timer controlled,
4 outlets on right side are always on.
3. Check the settings of the timer are correct.
4. Turn the switch on.
RATINGS
120Vac, 15A 60Hz 1800W
Limited One Year Warranty
AmerTac™ warrants this product to be free from defects in material
and workmanship for a period of one year from the date of purchase.
AmerTac's obligations are limited to repairing or replacing any defective
unit and are effective only if such units are returned within one year
of the purchase date to AmerTac, 250 Boulder Drive, Breinigsville, PA
18031. Warranty void if damage is due to misuse or improper installation.
In no circumstance will AmerTac be liable for consequential or incidental
damages relating in any way to this product.
Questions?, ¿Preguntas? 201.661.9945
©2011 AmerTac™
Saddle River Executive Centre,
One Route 17 South, Saddle River, NJ 07458
www.amertac.com
Made in China