EINHELL TC-SD 3,6 Li-Ion Kit Manual De Instrucciones Original página 21

damage the battery.
Check that your mains voltage is the same as that
marked on the rating plate of the battery charger.
Plug the battery charger in the plug socket and
connect the charging cable to the charging con-
nection.
The charging process starts as soon as
the charging cable is connected to the charging
adapter.
The red LED (4) will come on to indicate that the
battery pack is being charged.
The charging control lamp (4) goes out when
charging is completed.
Charging with the docking station/
charging cradle (Fig. 2b)
Connect the USB charging cable (9) to a portable
USB charger (not supplied) or USB port. Then
plug the other side of the USB charging cable (9)
into the charging socket on the docking station
(15) and place the screwdriver/flashlight on the
docking station to allow the tool to be charged.
The indicator lamps (11) on the docking station
will light up in the order in which the tool is char-
ged. When the tool is fully charged, all 4 indicator
lamps will light up.
Notice! The handle may become a little warm du-
ring the charging process. This is normal.
If the battery fails to charge, please check
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts of the charging unit
•
If the battery still fails to charge, send
the charging unit
•
and the screwdriver
to our customer service center.
Timely recharging of the battery will help it serve
you well for a long time. You must recharge the
battery when you notice that the power of the
cordless screwdriver drops.
6.2 Changeover switch (Fig. 3/Item 10)
The slide switch above the On/Off switch is for
setting the direction of rotation of the cordless
screwdriver and for preventing the cordless
screwdriver from being switched on inadvertently.
You can select between clockwise and counter-
clockwise rotation. Change the direction of rotati-
on only when the equipment is at a standstill.
If you fail to observe this point, the gearing may
become damaged. When the slide switch is in the
middle position, the On/Off switch is blocked.
Anl_SA_TC_SD_3_6 Li_Ion_Kit_SPK8.indb 21 Anl_SA_TC_SD_3_6 Li_Ion_Kit_SPK8.indb 21
GB
6.3 On/Off switch (Fig. 3 / Item 9)
Press the On/Off switch to switch the cordless
screwdriver on. Release the On/Off switch again
to switch it off .
6.4 LED lamp (Fig. 3/Item 14)
The LED lamp (14) can be used in poor lighting
conditions to illuminate the area where you want
to screw. To switch ON, press the switch (14) and
to switch OFF press the switch (5) again.
6.5 LED torch (Fig. 2/Item 7)
The cordless screwdriver has an integrated LED
lamp (7) on the handle to illuminate areas with
poor lighting. To switch it on, push the on/off
switch of the LED torch (6) down. Switching off
works in reverse order.
6.6 Angle setting (Fig. 4/Item 7)
The screwdriver can be locked into 2 diff erent
angle settings. To do so, press and hold the lo-
cking button (7) and move the screwdriver into the
desired position. Then release the locking button
(7) again.
Caution! Before you switch on the screwdriver,
make sure that it is correctly locked in the angle
position in question.
6.7 Battery capacity indicator (Fig. 5)
Remove the cordless screwdriver from the char-
ging unit/charging station.
Press the button for the battery capacity indicator
(6). The battery capacity indicator (5) indicates
the charge state of the battery on 3 colored LEDs.
All the LEDs are lit:
The battery is fully charged.
The yellow and red LEDs are lit:
The battery has an adequate remaining charge.
Red LED:
The battery is empty, recharge the battery.
6.8 Torque setting (Fig. 5 / Item 2)
The torque for a particular screw size is set with
the setting ring (2). The torque is dependent on a
number of factors:
•
On the type and hardness of the material
involved
•
On the type and length of the screws used
•
On the requirements that the screw connec-
tion has to satisfy
The grating disengagement of the coupling in-
dicates that the selected torque level has been
reached.
Notice! Only ever adjust the setting ring
when the equipment is at a standstill.
- 21 -
21.12.2020 09:19:04 21.12.2020 09:19:04