Declaration Of Conformity - Avidsen 654105 Guia De Inicio Rapido

24V
Powered gates with actuator
24V
150kg
QUICK START GUIDE
1,75m
24V
150kg 150kg
1,75m 1,75m
OPTION
150kg
150kg
SOLAIRE
1,75m
1,75m
OPTION
150kg
SOLAIRE
1,75m
OPTION
SOLAIRE
Thank you for purchasing an automatic gate opener.
This document is a quick start guide detailing the main installation steps as well as the equipment required. To perform the installation,
please download the installation manual at the following address: www.avidsen.com
Warning: The safety instructions and installation instructions can be found in the installation manual. Follow all these instructions, as an
incorrect installation can cause serious injuries.
CONTENTS OF THE KIT
1 2
x 1
6
x 2
1 Actuator
2 Control unit
3 Flashing light
4 Remote control
EQUIPMENT REQUIRED (NOT SUPPLIED)
The tools and screws required for the installation must be in good condition and compliant with applicable safety standards.
cylinders attachment to the
flashing light
pillar:
- electronic panel
3m cable
10m cable
2 x 0.5mm2
2 x 1.5mm2
Reference: 654105
3 4
x 1 x 1 x 2
7
x 2
5 Gate mounting bracket
6 Pillar mounting bracket
7 Label for the override device
drilling the
pillar
drilling into
the gate
attachment of the attachment of the
brackets flashing light onto the
onto the pillars:
INSTALLATION
Safety guidelines: please refer to the installation manual for all safety instructions.
To perform the installation, please download the installation manual at the following address: www.avidsen.com
V1 Overview:
The cables used must be appropriate for outdoor use (such as H07RN-F for example).
The cable run between the two pillars must comply with applicable standards (NFC 15-100).
The geared motor power cable must run 80cm deep with red warning mesh.
Control
unit
1
List of cables:
1
2
5
x 2
3
4
The installation is a 4-step process:
1. Installation of the actuators on the pillars and gate, and of the electronic panel.
2. Electrical connection of the motors and electronic panel to the mains. This connection must be performed by qualified personnel
(electrician, etc.).
3. Adjustments and operation:
Warning: Only switch on the electronic panel once all connections have been made.
- Read the installation manual chapter on simple adjustments.
- Launch the movement self-learning programme (press "+" for 3 seconds)
- Programme the remote controls:
- Press "-" for 3 seconds
- Press "OK"
- Press the remote control button to be memorised
- Repeat the operation for each remote control
- Choice of operating mode:
By default, automatic closing is deactivated. To activate it, you must install a pair of photocells (optional)
4. Operational testing: To familiarise yourself with the automatism and ensure its proper operation, read the chapter on usage and conduct operational tests (opening/closing, initiate
obstacle detection, cut the photocell beam (optional)). Upon completion of these tests, you may have to modify certain settings (e.g. motor power).

DECLARATION OF CONFORMITY

With the RED directive Avidsen declares that the following equipment: Powered swing gates reference 654105
Complies with the RED 2014/53/EU directive. Its conformity has been assessed pursuant to the applicable standards in force:
• EN 301489-3 V1.6.1
• EN 301489-1 V1.9.2
• EN 300220-1 V2.4.1
• EN 300220-2 V2.4.1
• EN 55014-2 :1997+A1 :2001+A2 :2008
• EN 55014-1 :2005+A1 :2009+A2 :2011
• EN 61000-3-2 :2014
• EN 61000-3-3 :2013
• EN 60335-1 :2012
• EN 60335-2-103 :2003 + A11 :2009
pillar
The remote control included with the abovementioned product complies with the RED 2014/53/EU directive. Its conformity has been assessed pursuant to the applicable standards in
force:
• EN 301489-3 V1.6.1
• EN 301489-1 V1.9.2
• EN 300220-1 V2.4.1
• EN 300220-2 V2.4.1
• EN 60950-1 :2006 + A11 :2009+A1 :2010+A2 :2013
Chambray les Tours, date: 26/09/2017
Alexandre Chaverot, CEO
flashing light
cylinders
4
2
3
Inner side of the property
Connection Cable
Cable 3 x 2.5mm2 (more than 30m long)
230Vac power line
Cable 3 x 1.5mm2 (less than 30m long)
Left motor Cable 2 x 1.5mm²
Right motor Cable 2 x 1.5mm²
Flashing light Cable 2 x 0.5mm²
Max length
Unlimited
10m
10m
3m