Operation Details - bem wireless speaker trio Manual Del Usuario

Operation Details

Power on / Power off
Base : Press the power button to turn on the base of
Speaker Trio. The Bluetooth© indicator will light up
to signify the unit is on and ready to be paired. Press
the power button again to turn off the base and the
Bluetooth indicator light will go out.
Speakers: Press the power button to turn the speaker
on. The white light on the base will light up to signify
the unit is on. Press the power button again to turn off
the speaker and the white base light will also go out.
Please note, always make sure to turn on the
base unit before turning on the speakers
Play modes
Bluetooth mode: play an audio signal from the
connected Bluetooth© device.
AUX mode: play an audio signal from the connected
"wired" device.
Please note, if an Aux cable is connected to the
speaker it will not play music from Bluetooth©
connected devices.
Audio Use
Follow the above connection steps to pair a
Bluetooth© device with the Speaker Trio. At this point
you can send any kind of audio signal to your speaker
(music, video, gaming, etc.). Just use your device as
normal and the audio will play through your Speaker
Trio.
Controls
Pressing the + and - buttons will increase or decrease
the volume on the Speaker Trio. Please note that this
will not effect the volume levels on the connected
device.
Connection
Laptop / notebook / PC
As the Bluetooth© versions for these types of devices
varies greatly, the connection methods will differ
6
as well. If you can not connect with the Speaker Trio
using the previous method instructed you may need to
install a new version of the Bluetooth© driver. Please
reference the instructions of device for details.
Speaker Placement
The 3 individual speakers can be removed from
the Speaker Trio base to be set anywhere you like.
Approximate range is 80ft away from the base. The
Speaker Trio uses 5.8gHz signal so you're free to put
the speakers where you like!
AUX out
The Speaker Trio can also be used as a "bridge" to
wirelessly connect your devices to other speakers not
enabled with Bluetooth©.
Plug one end of the supplied Aux cable to the "AUX
OUT" port in the back of unit and plug the other end of
the cable to an "AUX IN" or "Line In" port on any other
speaker system
Please note, volume + & volume - on the Speaker Trio
lose function on this occasion and only the connected
Bluetooth© device or the connected speaker itself can
control the volume.
Charging
Connect your Speaker Trio base to an outlet using the
included power adapter. Place the speakers onto the
charging area of the base. The red backlight will slowly
flash during charging and goes out when it has reached
a complete charge (Approx. 3.5 hours).
Operation Details
(cont.)
Charging Indicator Light Modes
Red LED / Flashing Fast: Battery is low, charge the unit soon.
Red LED / Flashing Slow: Speaker Trio is charging
Red LED / Turned Off: Battery is fully charged
Note: if the unit has not been used in the past 7 days please charge for 10 minutes before using the Speaker Trio.
Troubleshooting
Issue: Pairing is unsuccessfully after multiple attempts
Solution:
Check if the Bluetooth© indicator light is on. If the indicator light is off, please press the power button
to turn the unit on. If the Bluetooth© indicator light still doesn't come on after pressing the power
button, please charge the unit.
Check for other Bluetooth© devices around the surroundings that may interfere with searching and
turn devices off.
Power off and then power on the unit to restart the Bluetooth© function of the unit or your Bluetooth
device
Unplug any cables plugged into the AUX IN, restart all devices and then attempt pairing again.
Issue: Interference or static during playback
Solution:
Avoid using the device between concrete or other building structures that may interfere with the
signal.
Please check if the battery level of the unit and the Bluetooth© device and charge if necessary.
For more troubleshooting help go to http://bemwireless.com
Storage
Power off the Outlet Speaker If the unit will not be used for an extended period of time.
Do not set the unit in a damp environment, high temperatures or in direct sunlight.
Maintenance
Power off the unit
Use a soft, dry, lint-free cloth and wipe gently
Do not use alcohol, benzene, thinners or other chemical detergents as these can cause the casing to
be warped or discolored
7