Material Supplied; Technical Data - Valex TM 400 Manual Del Usuario

MATERIAL SUPPLIED

The packaging includes the following items:
- Cropper
- Service key
- Operator's use and maintenance manual (this manual)
- Guarantee certificate (attached to this manual)
- Declaration of conformity (enclosed with this manual).
CHARACTERISTICS
The metal cropper is a modern and compact bench machine
for cutting metal objects. The work surface has an adjustable
vice with a built-in goniometer for cutting pieces of various
dimensions, which can have a slope of up to 45°. The outlet
for a dust suction system guarantees a work area which is
free from harmful and inflammable dust.
The abrasive disc is covered by strong metal sheet protections,
with one mobile articulated protection that progressively
uncovers the cutting area when the tool gets close to the
piece to be cut.

TECHNICAL DATA

Power supply voltage
Rated power
Insulation class
Weight
no. of revolutions of abrasive disc
Maximum abrasive disc diameter/hole
Acoustic pressure
Acoustic power
Vibrations
Abrasive disc replacement
GENERAL SAFETY REGULATIONS
1) It is forbidden for children, unskilled people and anyone who
hasn't read the warnings and instructions contained in this
manual to use the machine.
2) Always check the efficiency and integrity of the machine; it
can cause serious injury to the person using it.
3) Keep a safe distance from property, people and animals and
do not allow them to approach while you are working.
4) The operator is responsible for third parties in the machine
work area.
5) Do not use the machine in poorly ventilated areas or in the
presence of flammable and/or explosive liquids, powders,
gases or anything else of this kind.
6) Carry out work suitable for the machine's power, avoiding
dangerous and useless overloading for the operator and for
the working life and safety of the machine.
7) Make sure that any service keys have been removed before
using the machine.
8) Tie long hair back and do not wear bracelets or long
necklaces as they could get tangled in the moving parts
of the machine.
9) Always wear goggles, protective gloves and a dust mask
whilst working.
IMPORTANT! Individual protective equipment is essential
to safeguard your own safety and health.
10) Always stay in a safe and stable position when working
with the machine.
11) To stop the machine only use the stop switch.
12) Switch off the engine and disconnect the machine from
230 V~50 Hz
2200 W
II
19 kg
3750 min
-1
350/30 mm
LpA 102,8 dB(A)
LwA 115,8 dB(A)
5 m/s
2
cod. 1464620
7
the power supply when:
- the machine is out of use or unattended;
- you are servicing or cleaning the machine;
- you are replacing the tools.
13) Only use the machine in the ways described in this ma-
nual and do not alter the original layout in any way unless
explicitly stated in the instructions.
14) Periodically ensure that the ventilation openings of the
engine are perfectly clean and open.
15) Periodically check that all nuts and bolts are tight.
16) Replace abrasive tools when they are worn, damaged
or out of date.
17) Check that the covers, protections and mobile elements of
the machine are correctly assembled or positioned before
starting work.
18) check that the abrasive tools are constantly attached to
the respective support bases and are stable.
19) Keep fingers away from moving tools.
20) Switch off the machine immediately if the tools or the piece
being cut should break during work.
ELECTRICAL SAFETY REGULATIONS
1) The power supply voltage must correspond to that indicated
on the technical data plate. Do not use any other type of
power supply.
2) It is advisable to install a trip switch on the electrical power
supply line. Consult your electrician.
3) Do not use the machine in damp or wet areas or in the rain.
4) Check the conditions of the power supply cable every time
before using the machine; if there are any signs of damage
or deterioration do not use the machine, but take it to an
authorised service centre to have the cable replaced.
5) If you use a cable reel of extension lead, check that the power
of the machine is lower than the maximum power allowed
according to the extent that the cable is unwound.
6) Use an approved good quality extension cable. Keep it away
from the work area, from damp, wet, greasy and sharp sur-
faces and also from sources of heat and combustibles.
7) Keep children away from the devices connected to the
power supply.
STARTING UP
IMPORTANT! During all the start-up operations, the machine
must remain disconnected from the electric power supply.
Unpack the machine and check that all its parts are intact.
With one hand on the main handle (Fig. A pos. 1) keep the
disc protection casing down whilst turning the knob with the
other (Fig. A pos.14) in order to free the machine and let it go
slowly upwards until it is in its resting position.
Fasten the machine to the bench by bolts (not supplied), the
counter should not be constructed in flammable materials that
could catch fire due to sparks.
INSTALLATION OF THE ABRASIVE DISC (not supplied with
the machine)
IMPORTANT! Always wear protective gloves.
Loosen the screw (Fig. C pos. 1) and turn the cover (Fig.C
pos. 2) so as to uncover the screw (Fig.C pos.3)
Press the plug and keep it held (Fig.A pos.15) in the direction
of the disc so that it stops the rotation of the tool holder shaft,
inserting the stake connected to the lever in one of the two holes