Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALLATION INSTRUCTIONS
E-WPT Series
SURFACE CONDUIT MOUNTING
1.
Loosen the two mounting plate set screws using the supplied Allen
wrench to allow for removal of the mounting plate. Do NOT fully
remove the set screws. See Figure 1.
2.
At the desired mounting location, use the mounting plate as a
template to drill (4) holes in the mounting surface to attach the
mounting plate.
3.
Attach the mounting plate to the mounting surface using (4)
fasteners (supplied by others) appropriate for the mounting
surface. Make sure edge of the plate marked "TOP" is located
towards the top of the fixture.
4.
Remove the threaded 1/2" conduit entry plug from the chosen side
or top of the mounting base. See Figure 4.
5.
Hang the upper edge of the recessed area on the back of the
mounting base from the top of the mounting plate.
6.
Tighten the (2) set screws loosened in Step 1 to retain the
mounting box against the mounting surface.
7.
Open the fixture by loosening the (2) mounting base screws on the
side to allow the fixture door to swing open.
NOTE: Make sure all holes in grommet on back wall of mounting
base are sealed. If not, caulk holes to prevent water or insects
from entering.
8.
Feed the conduit and supply wires into chosen conduit entry
location.
9.
Complete the electrical connections per the Fixture Wiring section.
10. Close the fixture door and re-tighten the (2) mounting base
CARE AND CLEANING
screws.
1.
Shut off power before cleaning the fixture. To prolong the original
appearance, clean the fixture with clean water and a soft, damp
cloth only.
2.
Do NOT use abrasive cleaners or cleaners that contain alcohol.
Do NOT apply paints, solvents, or any other chemicals to the
light fixture because these substances could cause premature
deterioration of the finish.
3.
Do NOT spray the fixture with a high pressure washer.
FIXTURE WIRING
Fixture is equipped with universal volt driver 120-277V
(ie. 120V, 208V, 240V or 277V)
PHASE TO NEUTRAL WIRING 120/277V
1. Connect supply ground to fixture ground (green) lead.
2. Connect supply common to fixture neutral (white) lead.
3. Connect supply Vin to fixture hot (black) lead.
Tuck all wires carefully into wiring chamber ensuring that no wires
are pinched.
PHASE TO PHASE WIRING 208/240V
1. Connect supply ground to fixture ground (green) lead.
2. Connect supply L1 (Hot) to fixture neutral (white) lead.
3. Connect supply L2 (Hot) to fixture hot (black) lead.
Tuck all wires carefully into wiring chamber ensuring that no wires
are pinched.
www.e-conolight.com
|
LPN00685X0001A0_A
Document:
Created By:
TMT
FIGURE 3
Mounting Base
Set Screws
FIGURE 4
Set Screws
CAUTION: Changes or modifications not expressly approved
could void your authority to use this equipment.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved could void
your authority to use this equipment.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for
help.
CAN ICES-005 (B)/NMB-005 (B)
888.243.9445
|
FAX: 262.504.5409
Date
ECO#
Mounting Base
Mounting
Plate
Conduit Entry
Allen Wrench
FCC NOTICE
3-9-2020
011590
Mounting Base
Publicidad
