Publicidad
Registering your warranty
To register your warranty, fill in the online form at www.chacon.com/warranty
0.Introduction
Thank you for using this product.
• Please read the instructions carefully before using the device.
• Do not attempt to dismantle or repair the product yourself as it will invalidate the warranty.
1. Introduction to the product
1
Plug
2
LED indicator
3
Tune
4
Volume
5
Speaker
6
Pushbutton
7
Silicone plug
8
Name plate
9
Screw location
1.1. Installing the battery (push button)
1. Remote the cover located above the name plate.
2. Use pliers to remove the silicone plug
3. Use a Phillips screwdriver to loosen the screw.
4 / 5. Use a flat screwdriver to open the device.
6. Insert the CR2032 3 V battery (included)
7. Check that the gasket is correctly positioned before closing the unit.
NOTE: When you insert the battery, take care to observe correct polarity
(+/-) without damaging the battery.
1.2 Fitting the indoor and outdoor units
1.2.1 Outdoor unit (push button)
Open the transmitter using a flat screwdriver and separate the front and back sections.
Then, fix the rear section to an appropriate height on the wall using the two screws provided.
v1
TIP: For the installation, you will need a drill and a Phillips screwdriver.
IMPORTANT: Before drilling a hole in the wall, make sure that there are no cables or pipes that you could accidentally damage.
You can stick the transmitter at an appropriate height using double-sided adhesive tape (provided)
v2
NOTE: If you mount your push-button to a surface made of uPVC (polyvinyl chloride) or metal, please note that the transmission
range will be reduced.
1.2.2 Indoor unit (chime)
Connect the chime to a suitable socket with a voltage of 110~240V / 50~60Hz
Note: Choose a location that is not close to a heat source. Choose a location where the doorbell will be easy to see and hear.
2. Use of the product
Once you have fitted the battery to the outdoor unit (push button) and plugged in your indoor unit (chime),
there are just a few more steps before your new doorbell is working.
1. In order to synchronise your two units, you first need to connect your chime to a wall socket 110~240V / 50~60Hz.
2. Then press and hold the "tune" button on the side (see diagram) for 3 seconds. The chime LED will turn on and beep to indicate that it has
entered in pairing mode.
3. Within 15 seconds, press the push button to establish a connection between the two devices.
4. the synchronisation has been established. You can choose your tune via the tune button (see diagram).
5. You can adjust the volume of your receiver (chime) using the volume button (see diagram).
Note:
- If you hear 2 beeps, the connection has not been established in time. You need to start again at step 2.
- If you wish to add multiple receivers (chimes), you need to repeat the process from step 2.
- If the receiver rings for no reason while you are setting the code, it is possible that there is interference from another similar doorbell nearby.
If this is the case, reset the automatic learning code as described in point 5: Resetting the unit).
3. Changing the tune
If you wish to change the tune on your doorbell, simply press the "tune" button and choose the tune and the volume you want.
4. Adding a second transmitter
1. Press the "tune" button on the chime once
2. Then press the transmitter button (pushbutton)
3. The receiver (chime) makes a noise to indicate that the new code has been saved.
Note: One receiver can be synchronised with up to 2 transmitters.
5. Resetting the unit
1. Press and hold the "tune" button for 10 seconds.
2. The receiver LED will flash and you will hear 5 "beeps" to indicate that the procedure was successful.
NOTE: Do the same to remove interference due to possible chimes in the area. However, you will need to reconstruct the synchronization
between the receiver and the transmitter in accordance with Chapter 2 above: Use of the product.
6. The receiver (chime) does not ring
1. Check for discharged batteries in the transmitter and if the plug of the receiver is well installed.
2. Check if the batteries are inserted in the transmitter with the correct polarity.
3. Check that the two units are not too far apart. Bring them as close to each other as possible, making sure that they remain within the
operating range (300 m free field).
7. Safety tips
• The receiver is designed for indoor use only
• Do not install the transmitter on a metal surface or UPVC door frames, because that would shorten their operating range.
• Do not expose the units to high temperatures.
• Do not immerse the units in water.
• If you do not plan to use the unit for an extended period, such as when you are on holiday, please remove the battery from the transmitter.
• Incorrect use of the battery could damage nearby items and cause a fire or serious injuries.
• Keep the batteries away from children.
• Recycle used batteries in line with environmental protection regulations.
8. Technical specifications
• Radio frequency: 433.92 MHz
•Max radio-frequency power: <20mW (EIRP)
• Transmission range: 300 m (free field)
• Adjustable volume: 80 dB
• Choice of 36 tunes
• Flashing LED warning
Recycling
Don't throw batteries or out of order products with the
household waste (garbage). The dangerous substances that
they are likely to include may harm health or the
environment. Make your retailer take back these products or
use the selective collect of garbage proposed by your city.
For indoor use only
Support
www.chacon.com/support
EN
1
2
3
4
5
• Weatherproof button (IP44)
• Battery (outdoor unit): 1 x DC 3 V CR2032 (provided)
• Outdoor battery life: 1 year
• Plug-in doorbell: 220 -240 V, 50/60 Hz
• Dimension: 110 x 110 x 79.5 mm
• Push button dimensions: 32 x 80 x 17.5 mm
Declaration of conformity
CHACON declares that device 84164 conforms with the
requirements and provisions of Directive RED 2014/53/EU.
The complete text of the EU declaration of conformity is available
at the following Internet address: www.chacon.com/conformity
6
7
8
9
3V CR2032
Chacon S.A. • Avenue mercator 2 • 1300 Wavre • Belgium
Ref. : 84164
v1.0 201009
Publicidad
