Ego Power+ BCA1200 El Manual Del Propietario página 8

◾
Always ensure that the ventilation openings are kept
EN
clear of debris.
MAINTENACE AND STORAGE
◾
Disconnect the machine from the power supply
(i.e. remove the battery pack) before carrying out
maintenance or cleaning work.
◾
Use only the manufacturer's recommended
replacement parts and accessories.
◾
Inspect and maintain the machine regularly. Have the
machine repaired only by an authorized repairer.
◾
When not in use, store the machine out of the reach
of children.
OTHER SAFETY WARNINGS
◾
Avoid Dangerous Environments – Don't use
appliances on damp or wet slope.
◾
Keep guards in place and in working order.
◾
Keep hands and feet away from the cutting area.
◾
To reduce the risk of injury, never work on a ladder
or on any other insecure support. Never hold the
cutting unit above waist height.
◾
Check the cutting unit at regular short intervals
during operation, or immediately if there is a
noticeable change in cutting behavior.
◾
For best results, your battery should be charged in a
location where the temperature is greater than 5° C
and less than 40° C. Do not store it outside or in vehicles.
◾
If you are approached, stop the motor and cutting unit.
◾
Warn the operator of the danger of blade thrust
(only using with 3-teeth blade).
◾
Blade thrust may occur when the spinning blade
contacts an object that it does not immediately cut.
◾
Blade thrust can be violent enough to cause the unit
and/or operator to be propelled in any direction, and
possibly lose control of the unit.
◾
Blade thrust can occur without warning if the blade
snags, stalls or binds.
◾
Blade thrust is more likely to occur in areas where it
is difficult to see the material being cut.
◾
Do not attach any blade to a unit without proper
installation of all required parts. Failure to use the
proper parts can cause the blade to fly off and
seriously injure the operator and/or bystanders.
Discard blades that are bent, warped, cracked,
broken, or damaged in any way. Use a sharp blade
A dull blade is more likely to snag and thrust
(only using with 3-teeth blade).
8
BRUSH CUTTER ATTACHMENT — BCA1200
◾
A coasting blade/line can cause injury while it
continues to spin after the motor is stopped or
trigger is released. Maintain proper control until
the blade/line has completely stopped rotating.
◾
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
even when the tool is not operating. Take care when
performing maintenance or service.
◾
Do not wash with a hose; avoid getting water in
motor and electrical connections.
◾
If situations occur that are not covered in this
manual, use care and good judgment. Contact the
EGO Customer Service Center for assistance.
◾
Use only with EGO's battery packs and chargers listed
in fig.A.
SAVE THESE INSTRUCTIONS!
SPECIFICATIONS
Cutting Width
No-Load Speed
Weight
Recommended Operating Temperature
Recommended Storage Temperature
Measured sound power level L
WA
Sound pressure level at
operator's ear L
PA
Guaranteed sound power level L
(measured according to 2000/14/EC)
Front-assist handle
Valuation of
vibration a :
h
Rear handle
◾
The above parameters are tested and measured
equipped with power head PH1400E;
◾
The declared vibration total value has been measured
in accordance with a standard test method and may be
used for comparing one tool with another;
◾
The declared vibration total value may also be used in
a preliminary assessment of exposure.
30 cm
5000/6000 min
-1
1.82 kg
0°C-40°C
-20°C-70°C
96.5 dB(A)
K=1.88 dB(A)
84.5 dB(A)
K=3 dB(A)
98 dB(A)
WA
3.3 m/s
2
K=1.5 m/s
2
1.9 m/s
2
K=1.5 m/s
2