YATO YT-85001 Manual De Instrucciones página 18

GB
Before starting work, prepare the area. You should remove the stones, pieces of wood, branches, wires, bones and other foreign
objects, which can cause damage to the grass trimmer or will be thrown out during the operation.
When working with the blade there is a risk of blade rebounding towards you and you being hit by the blade. To minimize this risk,
do not cut plant parts which are too hard. Rebounding occurs during the sudden stop of the blade during its operation, for example,
in the case of inability to cut a bush. Such stoppage results in rotation of the device in opposite direction to the rotation of blade. To
prevent rebound phenomenon and its consequences use extreme caution when working with the blade. Do not place body parts
in the area of the possible movement of the blade after rebounding. Maintain proper posture and balance during the work time.
Hold the tool handles fi rmly and always use the supplied harness or sling. The grass trimmer rebound can lead to the fall down of
its operator and endanger the operator for contact with rotating blade. The blade should be sharpened.
Turn the engine on in accordance with the instructions, pay attention to the feet, hands and other body parts, whether they are
away from the cutting element. Do not keep the hands, feet and other body parts in the vicinity of the rotating parts.
Stop the engine when:
- every time when you need to go away from the device,
- before cleaning, checking, or servicing the device,
- after striking by a foreign object. Check whether the grass trimmer is damaged and, if necessary, make repairs, before restarting.
- if the device begins to vibrate excessively (check immediately).
- during handling and transportation of the device.
ATTENTION! After stopping the engine, the cutting unit rotates for some time. Wait until it stops.
Always observe your surroundings and keep alert to possible threats, which may not be realized due to the noise of the device.
The tool produces a low-intensity electromagnetic fi eld. The electromagnetic fi eld may aff ect the work of electrical equipment
located near this tool and cardiac pacemakers. Before you start the work it is recommended to consultat your doctor and / or
manufacturer of the cardiac pacemaker.
TRANSPORT, MAINTENANCE AND STORAGE
Attention! Disconnect the spark plug wire before installation, adjustment, changing accessories or storage of the device.
This will allow to avoid accidental starting of the device.
While the grass trimmer is not in use, store it in a dry, secure place, out of reach by
outsiders.
Be careful when adjusting the machine to avoid getting your fi ngers between moving cutting elements, and
fi xed parts of the grass trimmer. Make sure that the used cutting element is of the correct type.
Before the grass trimmer transporting, empty its fuel tank.
Exchange in order to maintain security, worn or damaged parts. Use only genuine spare parts. Usage of spare parts, which are
not original, can increase the risk of failure and lead to injury. The grass trimmer should be repaired only in authorized services,
using original spare parts. This will minimize the risk of accidents and damage to the equipment.
The grass trimmer should be stored in a dry, closed room with good ventilation. When storing for extended periods
of time, empty the fuel tank and the fuel installation. Do not keep the grass trimmer with fuel in the tank. The grass trimmer should
be a subject of maintenance treatment as it is described in the manual.
The blade of grass trimmer should be protected during transport. Protection must remove before you start.
Keep in the proper condition all nuts, bolts and screws, to be certain that the device will be working safely.
GRASS TRIMMER OPERATING
Preparing the grass trimmer for operation
Before its fi rst use, you must install the cutting element, which is corresponding to a given work: the head of the cutting line or
blade, cutting element cover the additional handle and belt-harness.
The head of the cutting line should be used just to mow the grass. Use the blade to cut shrubs, woody plant shoots, etc.
In order to mount the guard of cutting element you should fasten it with the screw to spindle cover (II). The provided cover is ap-
propriate for work with the cutting line and blade as well. On cover the blade is fi xed, it is used for automatic shortening of the line.
If the blade is equipped with protection you should remove it before you start using the line for your work.
Mount the cutter handle. To dismount the upper part of the handle clamp, remove all screws. Next, place the handle connector
in the lower part of the clamp and mount the upper part of the clamp. Connect both parts of the clamp by screws (III). Select the
clamp location such that it is not necessary to excessively reach for them. In case of observance of hand exhaustion, numbing, or
pain during work, stop working, stop the engine and change position of handles to the more comfortable one.
Connect both parts of the cover of the drive shaft. To do this, loosen the clamp knob that connects the driving shaft covers, and
then press and hold the lock lever (IV). Insert the lower cover into the clamp and make sure that the hook of the lock reaches
the hole in the cover. Secure the connection by tightening the clamp knob (IV) to lock both parts of the driving shaft covers with
respect to each other.
Depending on the supplied equipment you should put on the belt or harness (V). The length of strips should be adjusted so they
are not pressing the operator's body, but at the same time they do not move during the operation. The grass trimmer can also
O R I G I N A L I N S T R U C T I O N S
18