Felisatti RF12/710 Instrucciones De Servicio página 5

- Lower the turret adjustment screw until it comes into
contact with the turret.
- Tighten the nut on the turret adjustment screw.
Note: The turret has 4 fixed positions which can be
adjusted to any position of the guide. Each position is in
increments of 3 mm and is calibrated by the manufac-
turer with the settings indicated on the label.
INSTRUCTIONS FOR CHANGING THE TEMPLATE
(Fig.6)
Adjusting the studs.
1. Remove the bit and instead put the pivot (P).
2. Loosen the fixing bolt (R).
3. Place the template (Q) and set it to position depend-
ing on the bit diameter being used.
4. Manually tighten the pivot support (S) until it hits the
stop and tighten the fixing bolt (R).
5. Remove the template (Q) and the pivot (P) and place
the corresponding drill bit.
6. Repeat the same operation on the second bit.
PERFORATING ACCORDING TO COURSE LINES
On the folding base (C) there are three marks of
which the right and the left correspond to the centre
of the bits.
- Position the machine over the object and adjust it with
the help of the markers.
- Position the rotating stop over the object with your free
hand.
- Start up the machine and push the motor cover (M)
forwards until it hits the stop.
- Remove the motor cover (M) and disconnect the
machine.
PERFORATING WITH THE ADJUSTMENT PIN (Fig.8)
The base (D) has two flexibly adjustable pins (L)
allowing perforations be made while maintaining a
fixed distance between the outside border of the
object being worked on. The machine can be posi-
tioned to the left or right of the object to be worked
on as required.
- Place the machine over the object to be worked on,
inserting one of the pins (L) and positioning another on
the outside border.
- Place the folding base (C) on the object to be worked
on, start up the machine and push the motor cover (M)
forward until it reaches the stop.
- Remove the motor cover (M) and disconnect the
machine.
DUST EXTRACTION
WARNING! Always make sure that the tool is switched
off and unplugged before fitting or removing any dust
extraction device.
Dust extraction keeps the workplace clean, prevents
dust build-up in the air and facilitates waste elimination.
CAUTION: A suction extractor should always be used
that has been designed in accordance with the applica-
ble directives in relation to dust emission. The flexible
hoses of conventional vacuum cleaners fit directly onto
the dust extraction nozzle.
ACCESSORIES
Accessories and their corresponding order number can
be found in our catalogues.
MAINTENANCE AND CARE
WARNING! Always unplug the machine before carrying
out work on it.
- Inspect the mounting screws: Regularly inspect
all the mounting screws and ensure they are firmly
tightened. Should any screw be loose, tighten it
immediately. Failure to do so could put you at se-
rious risk.
- Motor maintenance: Always take the greatest care
over this and make sure that the motor winding is
not damaged and does not become wet with oil or
water.
- The vents should always be kept clean and free of
obstacles.
- Clean the machine thoroughly after each use. Blast the
motor regularly with compressed air.
- Check that the mains lead is in good condition. If it is
not, take it to an Official Service Centre to have it
replaced.
- Brush replacement: Brushes must be replaced
when length reaches 8 mm or less. To do so,
please contact an authorized after sales service
center. We recommend that every other time you
take a tool to an after sales service centre for brush
replacement, you also order a general service
(cleaning and lubrication).
- Use only Felisatti accessories and spares. Parts the
changing of which is not covered in this instruction
manual, should be replaced in a Felisatti Official Ser-
vice Centre (See Warranty/Official Service Centre ad-
dress leaflet).
Do not dispose of electric tools in
the household waste!
In accordance with European Directive 2002/96/EC
relating to old electrical and electronic appliances and
its translation into national law, used electric tools must
be collected separately and recycled in an ecologically
desirable way.
WARRANTY
See general warranty conditions printed on the attached
sheet.
NOISE AND VIBRATION
This tool has been designed and made to reduce noise
to a minimum. However, in spite of this, in certain
circumstances the maximum noise level in the place
of work could exceed 85 dBA. In this case, the op-
erator should wear ear protection.