Technical Data - Siemens SENTRON 4DI/2DO Instructivo

SENTRON
4DI/2DO Expansion Module
Operating Instructions
Read and understand these instructions before installing,
operating, or maintaining the equipment.
DANGER
!
Hazardous voltage.
Will cause death or serious injury.
Turn off and lock out all power supplying this device
before working on this device.
CAUTION
Reliable functioning of the equipment is only ensured with
certified components.
Important note
The products described here were developed to perform safety-oriented func-
tions as part of an overall installation or machine. A complete safety-oriented
system generally features sensors, evaluation units, signaling units, and reliable
shutdown concepts. It is the responsibility of the manufacturer to ensure that a
system or machine is functioning properly as a whole. Siemens AG, its regional
offices, and associated companies (hereinafter referred to as "Siemens") cannot
guarantee all the properties of an entire plant, system or machine that has not
been designed by Siemens.
Nor can Siemens assume liability for recommendations that appear or are
implied in the following description. No new guarantee, warranty, or liability
claims beyond the scope of the Siemens general terms of supply are to be
derived or inferred from the following description.
Application
The 4DI/2DO expansion module is designed for use with the
SENTRON PACxxxx Power Monitoring Devices.
The 4DI/2DO expansion module integrates SENTRON PACxxxx Power Monitor-
ing Devices into power distribution systems, manufacturing equipment and pro-
cess systems via digital outputs and digital inputs.
Furthermore these systems can be connected via digital signals to the
SENTRON power management system.
Required tools for installation
See Figures 2 and 4. To connect cables with end ferrules to the screw terminals,
you also require a crimping tool in accordance with EN 60947-1.
Mounting and connecting
Mount the expansion module before starting up the SENTRON PAC. Observe
the ESD guidelines.
a) Always hold the expansion module by the plastic enclosure.
b) Ensure safe isolation from supply.
c) Discharge yourself.
d) Mount the Power Monitoring Device.
e) Connect the current terminals and voltage terminals to the
SENTRON PAC.
Mounting steps see Figure 3.
(1) Connect the expansion module to the SENTRON PAC with the aid of the
guide and the anti-twist element.
(2) Tighten the screws connecting the expansion module to the
SENTRON PAC with a torque of 0.5 Nm.
(3) Connect the cables to the screw terminals of the terminal block.
(See Figures 4 to 7)
(4) Ensure sufficient strain relief for all connected wiring.
2
Configuring
The expansion module is configured on the display of the SENTRON
Power Monitoring Device or in SENTRON powerconfig.
Figure 8: Setting the configuration data for the digital inputs on the display of
the SENTRON PAC.
Figure 9: Setting the configuration data for the digital outputs on the display
of the SENTRON PAC.
Please refer to the manual for the SENTRON PAC for configuration details. This
manual can be found on the CD for the SENTRON PAC Power Monitoring
Device and on the Internet (see Technical Assistance)..

Technical data

Power supply From SENTRON PAC
Electrical isolation between 500 V
SENTRON PAC and the
4DI/2DO interface
Insulating voltage Max. 500 V
Degree of protection IP20
Permissible degree of pollution 2 in accordance with IEC 61010–1:2001
Weight Approx. 38 g
Dimensions of enclosure with 70.3 x 43 x 22
terminal block in mm
(H x W x D)
Mounting depth of 73
SENTRON PAC with
PAC 4DI/2DO
expansion module in mm
Enclosure design VDT 3400 structure 36
Tolerances according to DIN 16901:1982–11
Cooling Passive air cooling
Flammability class V–0
Digital inputs:
Number 4
Type Internal power supply
External operating voltage 0 ... 30 V DC (optional)
Input resistance
 1 k
"1" signal detection
 100 k
"0" signal detection
Input current
 2.5 mA
"1" signal detection
 0.5 mA
"0" signal detection
Digital outputs:
Number 2
Type Bidirectional
Design/function Switching output or pulse output
in accordance with IEC 62053-31 Class B
Rated voltage 0 ... 30 V DC, typically 24 V DC
(SELV or PELV supply)
Output current for "1" signal
 50 mA (internal resistance 55 )
Continuous load
 130 mA for 100 ms
Transient overload
 0.2 mA
Output current for "0" signal
7KM9200-0AB00-0AA0
English
PAC
3ZW1012-7KM03-1AA0